Empyreal solutions
Contact Us

Address-
1. Near mastermind school,
b9,Krishna nagar, New sanghvi,
Pune
2. Near Swamy hotel,
Ganesh angan building,sambhaji chow,
akurdi, Pune

Email-
empyrealsolutions13@gmail.com

Mobile No.-
+91 8149955666,
+91 9762884689

Mechanical & Automobile based Projects - Empyreal Solution
16087
page,page-id-16087,page-template-default,ajax_fade,page_not_loaded,,qode-theme-ver-5.3,wpb-js-composer js-comp-ver-4.3.4,vc_responsive

Mechanical & Automobile based Projects

Mechanical Enggineering Project List 2015-16
PROJECT LIST

AUTOMOBILE BASED PROJECTS:-
AU001 Pre Drive Two Wheeler Authorization with Turbo on Demand
AU002 Optional acceleration circuit to increase the Fuel Efficiency of single cylinder Petrol Engine by using double Carburetor method
AU003 Three methods of emission and Efficiency comparison- Petrol Engine, acetylene mixed with LPG and Petrol mixed with Acetylene
AU004 Cold start Performance enhancement of Motor Cycle with catalytic converter using latent heat storage System
AU005 Enhancing performance of IC Petrol Engine by Peltier Air preheating System along with Exhaust Gas heat recovery System.
AU006 Automatic Brake failure detector and ignition locking System for Automobile
AU007 Pneumatic disc Brake System by using Engine Exhaust gas
AU008 Two Engine Synchronization for Four Wheeler
AU009 Fabrication for Converting Waste Plastic in to Diesel Fuel
AU010 Automatic Car washing System by using IR Sensor
AU011 Increasing the volumetric Efficiency of Four Stroke Engine by using ATEG
AU012 Electrical Power production and Water pumping from Speed Breaker
AU013 Fabrication of Anti-theft Steering System
AU014 Fabrication of Magnetic Fuel Modifier for Petrol Engine
AU015 Fabrication of Four Wheel Three mode Steering System
AU016 Fabrication of Hydrogen and Petrol mixed Engine
AU017 Fabrication of Electric Powered Gear Bike
AU018 Hub center Steering System for Two Wheeler
AU019 Fabrication of Six leg kinematic walker
AU020 Solar E-bike with Regenerative Braking System
AU021 Pneumatic Bumper and Breaking with head light dim & bright controller
AU022 Pneumatic controlled steps in Bus with Break locking System
AU023 Multi-purpose Agriculture Vehicle for Seed sowing with weed remover and fertilizer sprayer
AU024 Pneumatic Automatic Gear changer for Two Wheeler
AU025 Fuel Efficiency improvement in Petrol Engine by using Water injection
AU026 Fabrication of Hydro-Pneumatic moving Vehicle
AU027 Electrical Power Generation and Refrigeration by using waste heat from IC Engine
AU028 Fabrication of Man Powered Car
AU029 Fabrication of Water Fuel Engine
AU030 Belt model based Stair Climbing Wheel Chair
AU031 Cam shaft operated Automatic Gear change for Two Wheeler
AU032 Safety System to avoid Accident when Driver in Sleep
AU033 Fabrication of parallel Car parking System
AU034 Automatic Pneumatic Bumper and Break actuation before collision
AU035 Numerical analysis and experimental validation of a single cylinder Diesel Engine with Water injection
AU036 Fabrication of Super charging an Engine using Vehicle suspension
AU037 Fully covered Two Wheeler with Automatic extra Wheel balancing System
AU038 Fuel Efficiency Increasing System by using Turbo Charger with Brake cooling System
AU039 Enhancing the IC Engine Performance by Using the Electrolysis and Preheating Process
AU040 Automatic air delivered System based on density of oxygen in Car cabin
AU041 Increasing the Efficiency of Vehicle at higher altitude with Load Test
AU042 Combined Economic and Power mode by using super Charger and Hydrogen Fuel
AU043 Efficiency monitoring of a two Stroke Petrol Engine by using Air heat exchanger
AU044 Efficiency Increasing System by using preheating method
AU045 Active brake torque vectoring in differential unit for quick turning
AU046 Fuel Efficiency improvement by using Acetylene powered Engine
AU047 Water Fuel (Hydrogen/Brown gas) Engine with Load Test
AU048 Exhaust Gas heat recovery (TEG) Power Generation System
AU049 Modified Reverse Gear Two Wheeler for handicapped people
AU050 Triangular air Compressor with Common Compression Chamber
AU051 Air Engine with Load Testing (Dynamo Meter) Arrangement
AU052 Fuel Efficiency comparison of Air preheated System and Water injection System
AU053 Experimental investigation of an Air Conditioning System drive by Engine
AU054 Fuel Efficiency Increasing System by using peltier Air preheated System
AU055 Compressed air production using Vehicle suspensor
AU056 Automatic Vehicle over Speed controlling System for School Zone
AU057 Dual Power Generation System for Automobile (thermoelectric + Exhaust Gas Power Generation)
AU058 Digital Automatic Tyre pressure inflation and Monitoring System
AU059 Magneto Rheological Fluid (MRF) Braking System
AU060 Exhaust Gas recirculation System (EGR) for Two Wheeler
AU061 Fabrication of Automobile Exhaust heat Refrigeration System
AU062 Button operated Electro-Magnetic Gear shifting System for Two Wheeler
AU063 Generation of electricity using the flow or velocity of Vehicle Exhaust gas
AU064 Fabrication of Brown Gas Engine for Two Wheeler
AU065 Fabrication of Mono Wheel Bike
AU066 Water Fuel Engine with Power Generation
AU067 Tilting Three wheeler with Hybrid System
AU068 Increasing the Efficiency of Turbo Charger during low Engine Speed by turbo-lag reduction
AU069 Fabrication of Air powered Cycle
AU070 Automatic fire safety System for Fuel tank and Engine
AU071 Design and development of downdraft Gasifier for operating CI Engine on dual Fuel mode
AU072 Automatic Speed Breaker on time demand
AU073 Fabrication of Ethanol Fuel Engine
AU074 Theojanson Walking Mechanism
AU075 Automatic Speed Breaker depending upon Vehicle Speed
AU076 Friction less Electro-Magnetic Braking System
AU077 Fabrication of Air bag System for Two Wheeler
AU078 Automatic Reverse locking System in hill station by using differential unit
AU079 Fabrication of Buggy with Solar Hybrid Vehicle
AU080 Anti-theft Wheel locking System with SMS alert
AU081 Fabrication of Steer-by-wire System for Cars
AU082 Fabrication of Solar Race Car
AU083 Automatic Pneumatic Bumper for Four Wheeler
AU084 Intelligent Gear transmission System with Active Helmet Vehicle
AU085 Automatic Motorized Four Wheel Steering Mechanism
AU086 Over Speed indication and Automatic Accident Avoiding System
AU087 Fabrication of Turbo charger for Two Wheeler
AU088 Eye blink sensor based Automatic Breaking and Bumper System
AU089 Three axis Pneumatic modern Trailer
AU090 Automatic Electro-Hydraulic Jack for Four Wheeler
AU091 Automatic Electro-Magnetic Gear transmission for Two Wheeler
AU092 Experimental study and Application in Nano fluid in Refrigeration
AU093 Electro-Magnetic Fuel conditioner for IC Engine with Load Test
AU094 Fabrication of Compressed air Production using Speed Breaker
AU095 Fabrication of 360 degree parking assistance System
AU096 Power Generation in highway using fast moving Vehicle
AU097 Fabrication of Self Energized Hybrid System for Car
AU098 A study of conversion of Diesel Engine to fully Biogas Engine
AU099 Fabrication of digital lock Fuel pump & Break locking System
AU100 Electro-Magnetic ABS for Two Wheeler
AU101 Power Generation from Pneumatic shock Absorber
AU102 Turbo jet Engine with Active Magnetic Bearing
AU103 Inbuilt Hydraulic jack coupled with Engine for Four Wheeler
AU104 Automatic Turbo charger at low and high Speed of Vehicle
AU105 Fabrication of pollution free Four Stroke Petrol Engine
AU106 Fabrication of Motorized Center stand for Cycle / bike
AU107 Automatic Distance Measurement and Braking System By using Ultrasonic Waves
AU108 Electrical Power Generation by road hump
AU109 Touch screen based Automatic Gear shifting System
AU110 Automatic Track Guided Vehicle (ATGV)
AU111 Fabrication of concept Bicycle (future Bicycle)
AU112 Viability of used sunflower oil as a substitute Fuel for Diesel Engine
AU113 Magnetic levitation flight landing System
AU114 Fabrication of Foldable Two Wheeler
AU115 Automatic mirror adjustment System for Car by using Sensor
AU116 Rear Wheel Steering for Trailer truck
AU117 Automatic head light alignment with Automatic hand Brake System
AU118 Emission control in two Stroke Petrol Engine by using multiple spark
AU119 Fabrication of Quad bike
AU120 Anti-Lock Braking System in Four Wheeler (ABS)
AU121 New high tech walking electric bike using solar power
AU122 Fabrication of Electro-Magnetic Engine
AU123 Exhaust Gas Power Generation by Blower
AU124 Heating and cooling jacket by using peltier effect
AU125 Button operated Pneumatic Gear shifting for Two Wheeler
AU126 Fabrication of Fully Automated Intelligent Vehicle
AU127 Catalytic converter for Two Wheeler
AU128 Fabrication of magnetic Fuel modifier in Diesel Engine with Water injection
AU129 Adaptable Multi Nut Fastener with Manual Height Adjustment System
AU130 Fabrication of Multi-utility Agriculture Vehicle
AU131 Fabrication of Automatic foot board Break System for Car
AU132 Fabrication of Smart Bike
AU133 Air Conditioning of Automobile using Engine Exhaust Gas
AU134 Modified Accident prevention crash guard by using Sensor
AU135 Automatic Foundation excavator Vehicle
AU136 Automatic Visitor Guided with material handling Vehicle
AU137 Automatic Brake failure indicator with Automatic Braking by Electromagnet coil
AU138 Fabrication of Auto clutch for Automobile
AU139 MHD Power Generation for Two Wheeler (Model)
AU140 Fabrication of Gyro stabilized Two Wheeler
AU141 Fabrication of porter governor
AU142 Automatic safety Systems for railway coaches
AU143 Fabrication of Eddy current Disc Braking System
AU144 Theojanson Mechanism for Walking Chair
AU145 Foldable Electric GoPed Two Wheeler
AU146 Fabrication of Rotary Smart Car Parking System
AU147 Fabrication of Pulse jet Engine (Model)
AU148 Fabrication of Four bar Cycle drive mechanism
AU149 Automatic clutch and brake System for Four Wheeler
AU150 Working of Air Conditional unit using damping effect of shock absorber
AU151 Electric scooter powered by Wind & Piezo Electric power
AU152 Pneumatic Disc Braking System (PDBS)
AU153 Fabrication of Solar Regenerative Cycle
AU154 Electro-Hydraulic Braking (EHB) System for Four Wheeler
AU155 Fabrication of Electric all-terrain Vehicle
AU156 Fabrication of Under Water Vehicle
AU157 Ethanol powered Vehicle with electric Motor drive at the front wheel
AU158 Automatic Vehicle Accident information through SMS
AU159 Motorized head light adjustment in Two Wheeler
AU160 Fabrication of Self running Bicycle
AU161 Kinetic Energy Recovery System (KERS) Cycle
AU162 Fabrication of Four Wheel Steering System
AU163 Fabrication of Exhaust back pressure regulation System
AU164 Fabrication of Motorized jack with work piece clamper
AU165 Electric Pulse Magnetic Braking (EPM Braking) System
AU166 Easy Car parking System by 90 degree Steering Mechanism
AU167 Automatic Speed Breaker for preventing Accident in school zone
AU168 Fabrication of Ferro fluid Power Generation
AU169 Fabrication of Automatic Car Covering System
AU170 Anti-theft Break locking with remote control System
AU171 Automatic Car Lifting jack with crank arrangement
AU172 Fabrication of Turbo charged Two Wheeler with zero Turbo Lag
AU173 Design & Development of Standing Wheel Chair
AU174 Fabrication of Piezoelectric Powered Cycle
AU175 Pneumatic multi nut’s spanner box with torque wrench
AU176 Shock Absorber test Rig using Cam and Sensors
AU177 Fabrication of Active Wheel
AU178 Fabrication of starter Motor over running prevention
AU179 Right angle Steering Mechanism in electrical Vehicles
AU180 Regenerative Compressed air System by suspension for Automatic Turbo lag reduction for Two Wheeler
AU181 Fabrication of Loading and unloading crane for ship
AU182 Air Compressor using quick return Mechanism
AU183 Experimental study of heat transfer enhancement in liquid piston cylinder
AU184 Joystick control Car drive mechanism for physically challenged people
AU185 Fabrication of Pneumatic Railway Track changer
AU186 Vehicle ignition control System by using RFID and finger print
AU187 Fabrication of Sweeper Vehicle
AU188 Sensor based Automatic Pneumatic disc Braking System
AU189 Fabrication of Solar Hybrid Car
AU190 Automatic Lifting Vehicle inbuilt attached jack
AU191 90 degree Four Wheel turning Steering Mechanism
AU192 Motorized screw jack with Solar panel and lighting System
AU193 Automatic tyre pressure inflation System
AU194 Intelligent Active Suspension System for Two Wheeler
AU195 Electro-Magnetic scrap collecting Vehicle
AU196 Fabrication of Foldable electric Bicycle
AU197 High efficient cooling System in a Car with help of BLDC motor
AU198 Hydraulic Lifting System for Four Wheelers
AU199 Sterling Engine with parabolic collector (Model)
AU200 Dual Brake Single liver System for Two Wheeler
AU201 Six leg Robot for Agriculture purpose which can spray Seed and water
AU202 Automatic Queries controlling System for Two Wheeler
AU203 Fabrication of Air powered Wheel chair
AU204 Semi-autonomous Multi-purpose cleaning Vehicle
AU205 Fabrication of weighing bridge in moving Vehicle
AU206 Power Generation from Hump using piezoelectric and Rack & Pinion
AU207 Automatic Magnetic Accident preventer for Train
AU208 Highway high Speed sensing and Automatic Pneumatic Braking System
AU209 Design and Fabrication of Opposite Piston opposite Cylinder (OPOC) Engine
AU210 Electro-Magnetic Braking on propeller shaft Two Wheeler
AU211 Solar grass Cutter with Automatic sun tracking System
AU212 Fabrication of Air brake System using Engine Exhaust gas
AU213 Hydraulic based emergency rescue ladder for fire Accident
AU214 Efficient Car Parking System for Four Wheeler
AU215 Experimental investigation & comparative study of Diesel Engine Fuelled with used transformer oil with Ethanol
AU216 Manual operated Multi nut tightner
AU217 Solar operated weed Cutter for Agriculture
AU218 Energy-harvesting shock absorber with a mechanical motion rectifier
AU219 Improved energy performance of a Refrigerating Machine using Water spray upstream of the Condenser
AU220 Motorized triangular air Compressor
AU221 Fabrication of Hub less Cycle
AU222 Automatic head lamp alignment System depending upon Steering
AU223 Automated Guided Vehicle (AGV)
AU224 Pneumatic visual landing Gear with Automatic Tyre pressure inflation System for aircraft
AU225 Effect of swirl induction by internally threaded inlet manifolds on Exhaust emissions of single cylinder Diesel Engine
AU226 Automobile suspension made of Hydraulic magneto rheological damper
AU227 Remote controlled motorized Hydraulic jack
AU228 Fabrication of Segway (Running model)
AU229 Pneumatic Speed Breaker with day and night control
AU230 Tread mill Bicycle with Power Generation
AU231 Fabrication of Hybrid driving seat
AU232 Fabrication of Cryogenic Engine using liquid nitrogen
AU233 Remote controlled scrap collecting Vehicle
AU234 Generation of electricity from cycling exercise
AU235 Automatic Car window opening by using sound and oxygen sensors
AU236 Fabrication of EGR assisted jet Compressor
AU237 Fabrication of Air Engine
AU238 Fabrication of Fuel less reciprocating (FLR) Air Engine
AU239 Electro-Hydraulic System for Automation in Four Wheeler
AU240 Automatic Motorized Centre stand for Two Wheeler
AU241 Automatic Electromagnetic retarder System using ultrasonic waves
AU242 Pneumatic try Cycle with turbocharged closed loop System
AU243 Fabrication of Screw shaft Engine
AU244 Sensor Operated Automatic Reverse Braking System
AU245 Fabrication of Automatic sweeping Vehicle
AU246 Wireless tyre pressure monitoring System
AU247 Automatic digital Tyre pressure inflation and deflation System
AU248 Total Electrical System for Automobile (headlights, taillights, indicators and wiper)
AU249 Automatic acceleration control in traffic signal
AU250 Fabrication of Diesel blended with Hydrogen Engine
AU251 Fabrication of Catalytic converter with PCM
AU252 Automatic Differential Unit locking System
AU253 Automatic Electro-Magnetic Clutch
AU254 Bio Gas Two Wheeler with Power Generation
AU255 Development of two Wheel drive Motor Cycle
AU256 Fabrication of Hydraulic lifting System for total car
AU257 Solar powered Peltier Car cabin cooling System
AU258 Fabrication of Aerodynamic design for Buses
AU259 Electronic Fuel Injection (EFI) System for Two Wheeler
AU260 Fabrication of All Terrain Wheel Chair
AU261 Fabrication of Water purifier Cycle
AU262 Fabrication of Motor bike with propeller shaft
AU263 Integrated automated Pneumatic jacks for Four Wheelers
AU264 Hydraulic parking attachment for car
AU265 Fabrication of Direct Drive wheel
AU266 Highways High Speed Sensing and Automatic Speed Braking System
AU267 Fabrication of Magnetically Levitated Train/Flight
AU268 Hybrid Vehicle with regenerative Breaking motor Cycle
AU269 Fabrication Automatic lawn mover
AU270 Remote controlled tilting handicapped Wheel chair
AU271 Automobile dual side wiper System with Mist control
AU272 Combined model of Automatic head light dim / bright System and Automatic hand Break release System
AU273 Fabrication of Bicycle Powered Wind Turbine
AU274 Automatic parking Breaking System for Four Wheeler
AU275 Development of Homogeneous Charge Compression Ignition (HCCI) Engine on electric motor Cycle
AU276 Magneto Hydro Dynamic (MHD) Braking System
AU277 Performance analysis of Evaporative Air cooled condenser
AU278 Combination of emergency, intelligence and anti-lock Braking System
AU279 LPG Gas Powered Two Wheeler
AU280 Advanced emergency Braking System
AU281 Fabrication of Fly car
AU282 Fabrication of Pneumatic Scooter excavator
AU283 Fabrication of Solar Wind Energy Vehicle
AU284 Intelligent Braking System in Four Wheeler (IBS)
AU285 Wheel chair using Joy stick and Touch screen
AU286 Fabrication of foldable helmet
AU287 Air preheating System by using waste heat in Automobile
AU288 Automatic Vehicle overload alert System
AU289 Regenerative Breaking System by using Pneumatic interface
AU290 Fabrication of Tamble Cycle with regenerative Electrical Cycle
AU291 Energy conversion from Roadways using kinetic motion
AU292 Fabrication of Methane Gas (Bio Gas) Engine
AU293 Fabrication of Safety bike
AU294 Solar grass Cutter with Water spraying Vehicle
AU295 Piezo-Electric Energy production from running Vehicle
AU296 Fabrication of Anti drown Vehicle
AU297 Automatic Steering control System for Automobile
AU298 Fabrication of Chainless string Cycle
AU299 Fabrication of Unaided Automatic Tri Cycle
AU300 Electronic assisted Hydraulic Braking System
AU301 Design and Fabrication of Automatic soil monitoring Robot
AU302 Power Generation from Speed Breaker using roller Mechanism
AU303 Fabrication of Multiple Car safety System in bumper
AU304 Fabrication of Magneto rheological clutch with Load Test
AU305 Shock observer Power Generation System
AU306 Button operated Hydraulic jack
AU307 Fabrication of Automatic Pneumatic jack
AU308 Design& Fabrication of Hotel serving Robot
AU309 Fabrication of Pollution free Four Stroke Petrol Engine
AU310 Fabrication of air ship
AU311 Automatic Railway Gate Controller
AU312 Fabrication of Solar E Cycle
AU313 Crane for multiple movements with holding Car and Lifting
AU314 Elimination of chain drive in Bicycle
AU315 Fabrication of Engine Drive Cycle
AU316 Automatic hand Brake System by using Pneumatic interface
AU317 Multi tasked smart Wheel chair for physically challenged people
AU318 Fabrication of Variable volume Engine
AU319 Power Generation from Speed Breaker by using Hydraulic System
AU320 Automatic Gear changer in Bicycle
AU321 Fabrication of Fuel cell bike
AU322 Cryogenic liquid nitrogen as a Fuel for zero emission Vehicle
AU323 Introduction of HHO Gas in turbojet Engine
MECHANICAL / PRODUCTION / MANUFACTURING BASED PROJECTS:-
ME001 Design & Development of semi-Automatic feeding Mechanism for small scale Poultry Farm
ME002 Motorized Coconut Dehusking Machine
ME003 Automatic Intelligent ingot feeder for pick and place machine
ME004 Fabrication of Automatic CNC Multi-axis drilling Machine
ME005 Automated paper cup Feeding and making Machine
ME006 Automatic wall painting sprayer Machine
ME007 Automatic paint spraying pick and place Equipment
ME008 Pneumatic CAN crusher with Automatic feed Mechanism
ME009 Fabrication of Automatic conveyor based Rice Batching Machine
ME010 Electrical Power Generation from Waste oil burning System
ME011 Multi-purpose Agro Machine for Seed sowing with weed remover and fertilizer sprayer
ME012 Dual Hacksaw Machine with width worth Mechanism
ME013 Motorized High Speed Four way hack saw Machine
ME014 Design of Automatic plastic separation module for municipal solid waste
ME015 Surface finish measuring Equipment with digital display
ME016 Automatic Three axis CNC milling Machine
ME017 Fabrication of Motorized shaper and slotter in a single Machine
ME018 Automatic Gear milling Machine using proximity sensor
ME019 Geneva conveyer with Pneumatic pin punch
ME020 Fabrication of smart cradle with timer
ME021 Fabrication of Activated Carbon Manufacturing Plant
ME022 Fabrication of Automatic T-Shirt folding Machine
ME023 Motorized Multi-purpose Machine by using cam Mechanism
ME024 Power production and Water pumping from Speed Breaker
ME025 Auto Indexing Gear cutting attachment for Pneumatic shaping Machine
ME026 Chip and Dust collecting Machine by using Blower
ME027 Pneumatic Hacksaw Machine with shaping attachment
ME028 Three axis Hydraulic Modern Trailer
ME029 Auto roll punching Machine using Geneva mechanism
ME030 VIVACE (vortex induced vibration aquatic clean energy) a new concept in generation of clean and renewable energy from fluid flow
ME031 Experimental study of control parameter in pulsed spray hot steel plate
ME032 Automatic weighing and Sealing Machine
ME033 Punching Machine using width worth mechanism
ME034 Metal polishing using Abrasive jet Machine
ME035 Emergency Rescue ladder for fire Accident for apartment
ME036 Ginger cutting, feeding and drying Machine
ME037 Design and Fabrication of Punching Machine using scotch yoke Mechanism
ME038 Fabrication of Motorized Embossing drilling Machine
ME039 Fully Automated potato Chip Slice making Machine
ME040 Salt Water purification and electricity production from steam Power plant
ME041 Plastic crushing and Injection Moulding Machine
ME042 Automatic drainage cleaning Machine and detection of toxic gases
ME043 Automatic Quick tool Retrieval System for Industry
ME044 Riser removal in the casting Pieces by Pneumatic piston
ME045 Automatic Multiple operation in a single Machine
ME046 Automatic PVC pipe Feeding and Cutting Machine
ME047 Automatic scrap collecting & Disposing Machine
ME048 Automatic paper rolling and Pneumatic sealing Machine
ME049 Dual ram shaper to reducing lead time increasing material removal rate
ME050 Fabrication of Electrode flux removing Machine
ME051 Fabrication of Pin on Disc wear testing Machine
ME052 Multipurpose sheet metal cutting and bending Machine
ME053 Fabrication of potato Peeling & slicing Machine
ME054 Tread mill Bicycle with Power Generation
ME055 Automatic moving from one tree to another tree rubber tapping Machine
ME056 Automatic vertical Board cleaner
ME057 Fabrication of Bore well child rescuing Machine
ME058 Semi Automated Areca Nut Collecting conveyor
ME059 Fabrication of Loading and unloading crane for ship
ME060 Button operated Motorized portable mini crane
ME061 Fabrication of Electronic Hack Saw Machine
ME062 Design and Fabrication of universal jaw
ME063 Joystick operated tool post for lathe
ME064 Mechanical CAN crusher by using quick return Mechanism
ME065 Automatic gate Open and Close System using IR Sensor
ME066 Double side hack saw Machine using scotch yoke mechanism
ME067 Fabrication of tilting vice
ME068 Fabrication of Motorized jack with work piece clamper
ME069 Pedal operated biomass briquetting Machine
ME070 Fabrication of sugarcane juicer Machine
ME071 Mini rice harvesting and threshing Machine
ME072 Pneumatic Machining Time Reduction in Shaping Machine
ME073 Tapping attachment in drilling Machine
ME074 Hydraulic operated sheet bend / bend Removing Machine
ME075 Fabrication of manual operated liquid pump
ME076 Salt Water converted to purified drinking Water by using pedal power
ME077 Fabrication of bomb calorimeter
ME078 Fabrication of Shot blasting Machine
ME079 Fabrication of bucket Wheel Escalator
ME080 Two stage Mechanical Water Pendulum oscillator
ME081 Automatic transformer heat reduction System
ME082 Design and Fabrication of hand operated fertilizer blender
ME083 Fabrication of Dual type grinding Machine
ME084 Cutting Machine by Four bar Mechanism
ME085 Pedal operated hydro Pneumatic vice
ME086 Fabrication of pedal operated vertical Hack saw Machine
ME087 Book reading aid for handicapped People
ME088 Contour Turning Attachment for Lathe
ME089 Gear type Injection Moulding Machine
ME090 Automatic Dish Washing Machine
ME091 Automated Pneumatic Drilling Machine
ME092 Fabrication of Pedal operated air Compressor
ME093 Pedal cranking mechanism for paddy wheat threshing Machine
ME094 Fabrication of vertical Lift Mechanism for Kattwyk Bridge
ME095 Hydraulic sheet cutting Machine
ME096 Fabrication of Sheet metal Rolling Machine
ME097 Rim type pedal operated Water pumping System
ME098 Fabrication of coconut grater and milk extractor
ME099 Fabrication of external vertical thread Cutting Machine
ME100 Fabrication of Mechanical seed thruster
ME101 Water pumping and Electrical Power producing pendulum kit
ME102 Automatic portable groundnut planting Machine
ME103 Design and Fabrication of Progressive Conveyor
ME104 Time Reduction for Duplex milling Machine
ME105 Electro-Magnetic Scrap collecting Vehicle
ME106 Fabrication of welding slag cleaning Machine
ME107 Fabrication of Indexing jig for milling fixture
ME108 Fabrication of Automatic sweeping Vehicle
ME109 Fabrication of Coconut Scraping Machine
ME110 Fabrication of mini vertical Lathe
ME111 Dual side Water pumping System by using scotch yoke mechanism
ME112 Fabrication of Motorized Multi-Engine Compressor
ME113 Fabrication of porter governor
ME114 Special purpose Machine for threading operation
ME115 Pendulum based Water pumping System
ME116 Automatic Fault egg sorting Machine
ME117 Fabrication of nut inspection conveyor
ME118 Foot operated plate cleaning Machine with Dryer
ME119 Fabrication of Seismic valve
ME120 Fabrication of Pneumatic Pellet press
ME121 Automatic boring mechanism for foundries
ME122 Pneumatic Paper cup making Machine
ME123 Cricket ball shooter for Armatures
ME124 Semi automated Wall plastering Machine
ME125 Pneumatic Coconut Husk remover & Shell Cutter
ME126 Pedal operated wet grinder with Cell phone charger
ME127 Semi-Automatic transfer Machine in conventional industries
ME128 A Positive Pressure Universal Vacuum Gripper
ME129 Fabrication of groundnut Thruster
ME130 Intelligent trolley for domestic cylinder
ME131 Fly Wheel based Water pumping System
ME132 Fabrication of mechanical spider
ME133 Power Generation from sea Water by MHD Power Generation method
ME134 Automatic multi point grease Gun
ME135 Low cost paddy harvesting Machine for agriculture
ME136 Fabrication of chocolate dispensing Machine
ME137 Fabrication of coin based shoe polishing Machine
ME138 Fabrication of Low cost sugarcane harvester
ME139 Fabrication of Axial piston pump
ME140 Horizontal and vertical tiles cleaner
ME141 Design and Fabrication of Friction stir welding Machine
ME142 Automatic sheet metal feeding and cutting Machine
ME143 Fabrication for converting waste plastic in to Bio Diesel Fuel
ME144 Fabrication of Abrasive Jet Machine
ME145 Automatic Agar Bhatti incense stick counting and packing Machine
ME146 Fabrication of switch board Cutter
ME147 Fabrication of Motorized Eccentric Forging Machine
ME148 Pneumatic multi Axis Welding Machine
ME149 Automatic scrap Compression Machine
ME150 High Speed Portable Pipe Cutting Machine
ME151 Fabrication of Vacuum assisted wall climber
ME152 Fabrication of Pepper thresher Machine
ME153 Fabrication of internal thread Cutting Machine
ME154 Three way motion for tool in ECM Machine
ME155 Remote controlled Water weed Cutter Machine
ME156 Automatic medicine dispenser for sugar patient
ME157 Automatic Spring De-coiler Machine
ME158 Automatic paper cutting using Geneva mechanism
ME159 Fabrication of low cost sugarcane harvester
ME160 Fabrication of Engraving Machine
ME161 Electro chemical drilling Machine
ME162 Development of low cost ball milling Machine
ME163 Automatic Drilling and Tapping Machine
ME164 Fabrication of Torsion (spring) testing Machine
ME165 Automation of Vibro cleaning process in a typical Die casting industry
ME166 Fabrication of conveyor automation with dimension inspection
ME167 Push operated Agriculture spray Pump for Garden
ME168 Motorized Pipe Cutting Machine using quick return Mechanism
ME169 Motorized Radial sheet bending and Cutting Machine
ME170 Pneumatic double side cutting time reduction in shaper
ME171 Fabrication Magnetic Power Generation
ME172 Hydraulic clamping device with power pack
ME173 Automatic Motorized oil mill Mechanism
ME174 Assistive limb for physically challenged people
ME175 Automatic Water level Sensing Crane
ME176 Generation of electricity from cycling exercise
ME177 Fabrication of Portable Slotting Machine
ME178 Fabrication of Pneumatic garage door opener
ME179 Fabrication of wood grooving Machine
ME180 Fabrication of drainage cleaning Machine
ME181 Fabrication of Rubber tree tapping Machine
ME182 Conveyor for quality control Machine
ME183 Design and Fabrication of human air bag
ME184 Fabrication of Double drum wet grinder
ME185 Fabrication of banana Fiber Extracting Machine
ME186 Pedal operated vertical hack saw Machine
ME187 Groundnut harvester with thresher
ME188 Design and Fabrication of Unmill for lathe
ME189 Fabrication of Air umbrella
ME190 Automatic Rubber processing Machine
ME191 Pedal operated Hacksaw with mobile charge
ME192 Fabrication of Motorized Agri Cutter
ME193 Fabrication of potato chips making Machine
ME194 Automatic grass cutting by using Sensor
ME195 Fabrication of Multipurpose Seed Sowing Machine
ME196 Motorized wood Cutting Machine
ME197 Fabrication of Centrifugal Pump apparatus
ME198 Fabrication of Eccentric punching Machine
ME199 Fabrication of Coir Making Machine
ME200 Fabrication of Motorized plant Cutter
ME201 Automatic Dosa making Machine
ME202 Fabrication of Multi-purpose Cutter
ME203 PLC based Automatic Rotary Water Bottle filling Machine
ME204 Fabrication of a low cost surface finishing Machine
ME205 Fabrication of Coconut tree sprayer
ME206 Digital Hydraulic Spring Testing Machine
ME207 Boiler automation with Digital steam Power plant
ME208 Fabrication of Coin Separator Machine
ME209 Pneumatic Double side cutter by using width work Mechanism
ME210 Reduction Power cost in induction furnace by alarm & Sensor System
ME211 Conveyor for Material dimension Rejection System
ME212 Pedal powered reverse osmosis Water purification System
ME213 Automatic Color code sensing punching Machine
ME214 Scotch yoke Mechanism based Water pumping System
ME215 Semi-Automatic weed remover in sugarcane farm
ME216 Fabrication of Pneumatic Gear tooth grinding Machine
ME217 Fabrication of Stir Casting Machine
ME218 Fabrication of Automatic Stretch wrapping Machine
ME219 Motorized external thread forming Machine
ME220 Fabrication of Mini milling Machine
ME221 Automated Pet feeder for Dog
ME222 Fabrication of Motorized radial Sheet bending Machine
ME223 Fabrication of Mechanical Seed crushing Machine
ME224 Shot Blasting Machine by using Abrasive powder
ME225 Fully Automated Hydraulic crane
ME226 Multi-purpose mini slog Cutting Machine
ME227 Fabrication of Automatic buffing Machine
ME228 Pedal cloth washing Machine with Drier
ME229 Three Axis Motorized Electrical crane
ME230 Furnace using infrared Lamp
ME231 Fabrication of Sound based Fire Extinguisher Machine
ME232 Fabrication of Foldable pram cum Cradle
ME233 External and internal grinding Machine attachment for lathe
ME234 Coconut tree climbing and cutting Machine
ME235 Fabrication of sewage Water treatment plant
ME236 Fabrication of Cake Decorating Machine
ME237 Fabrication of Paper Recycling Machine
ME238 Belt model based stair climbing Wheel chair
ME239 Eccentric shear cutting Machine
ME240 Semi-Automatic Road Reflector Stud Installation Machine
ME241 Fabrication of Rotary Kaller
ME242 Fabrication of Swirl gripper
ME243 Fitness equipment for localized electrical Power Generation
ME244 Multipurpose Keyway Attachments in Lathe
ME245 Remote controlled Tilting fan
ME246 Fabrication of Agricultural model pump
ME247 Multi use tool post grinder attachment for lathe
ME248 Fabrication of Modified sand Muller
ME249 Universal Multi Axis tool grinding Machine
ME250 Vertical abrasive belt grinder
ME251 Fabrication of Double axis Eccentric mobile crane
ME252 Fabrication of Pedestal Spot Welding Machine
ME253 Fabrication of Inspection Conveyor
ME254 Automatic Agar Bhatti stick counting Machine
ME255 Fabrication of Sweeping Machine
ME256 Generation of Power using municipal social waste
ME257 Remote controlled floor cleaning Machine
ME258 Fabrication of Pneumatic spring punching Machine
ME259 Temperature monitoring System in cupola furnace
ME260 Fabrication of Motorized blanking Machine
ME261 Portable coin shorter Machine
ME262 Automatic Pneumatic Gear Changer
ME263 Automatic Idli batter filling Mechanism
ME264 Fabrication of Electro-Mechanical ladder
ME265 Fabrication of biomass briquetting Machine
ME266 Pneumatic tool grinding Machine
ME267 Pneumatic Speed Breaker with day and night control
ME268 Button Operated Multi-Speed Gear box
ME269 Pedal operated Washing Machine for Cloth
ME270 Automated dual acting CAN crusher
ME271 Automatic open well cleaning Machine
ME272 Fabrication of Water soaked shoe cleaning System
ME273 Fabrication of Mechanical paint stirrer
ME274 Remote controlled motorized zip crane
ME275 Fabrication of Pneumatic brick handling Machine
ME276 Automatic work piece counting with belt conveyer
ME277 Optimization of process parameters in spark EDM
ME278 Fabrication of Pneumatic bore grinding Machine
ME279 Two stage mechanical amplifier
ME280 Pedal operated Solar Cell phone Charger
ME281 Fabrication of Solar hand massager Machine
ME282 Extraction of mercury from CFL waste
ME283 Fabrication of Hydraulic Machine vice
ME284 Fabrication of friction Welding Machine
ME285 Pedal operated hack saw and grinding Machine
ME286 Fabrication of Power Generation from Francis turbine
ME287 Blue tooth operated Mechanical arm
ME288 Design & Fabrication of Conveyor Automation
ME289 Fabrication of hand operated Edge folding Machine
ME290 Motorized triangular air Compressor
ME291 Fabrication of Beans Sheller Machine
ME292 Fabrication of eccentric pipe cutting Machine
ME293 Design and Fabrication of bar bending Machine
ME294 PLC based Automatic Pneumatic drilling Machine
ME295 Fabrication of Motorized chip crushing Machine
ME296 Square hole drilling Machine
ME297 Low cost automated hot stamping Machine
ME298 Fabrication of finding the life time of switches
ME299 Automatic circle marker by play ground
ME300 Pedal operated CAN crushing Machine
ME301 Electrical Power Generation by Road hump
ME302 Fabrication of Six leg kinematic walker
ME303 Pneumatic Spring End Grinding Machine
ME304 Air Compressor using quick return Mechanism
ME305 Fabrication of Pneumatic belt Conveyor
ME306 Semi-Automatic Water tank cleaner
ME307 Vacuum bag Moulding Machine
ME308 Advanced wireless Automatic digital pumping System for Agriculture using soil Sensor
ME309 Fabrication of Pneumatic Slotting Machine
ME310 Hydro Power plant with salt Water purification System
ME311 Pneumatic road marking Machine
ME312 Multiple roller handling Pneumatic manipulator
ME313 Fabrication of Groundnut shelling Machine
ME314 Hammering operation by using Vincicam Mechanism
ME315 Design & Fabrication of cotton baling Machine
ME316 Fabrication of Pedal operated drilling Machine
ME317 Hydraulic Pipe Bending Machine
ME318 Fabrication of tool cutting force dynamo meter on lathe
ME319 Experimental setup on Gasifier
ME320 Intelligent Motorized Wall Painting Crane
ME321 Pneumatic double axis excavator Arm
ME322 Multi-purpose Agri Cutter
ME323 Pipe line turbine with Power Generation
ME324 Fully automated chapatti making Machine
ME325 Fabrication of Hydraulic Sheet Sensing cutting Machine
ME326 Vacuum conveyor for industrial Application
ME327 Motorized screw conveyor for material transport
ME328 Fabrication of Briquette burner
ME329 Fabrication of Pneumatic plastic crushing Machine
ME330 Fabrication of Pedal dish Washing Machine
ME331 Bio-Diesel extraction from waste plastic material
ME332 Pneumatic Multi Axis Modern Truck
ME333 Fabrication of Shaft run out checker Machine
ME334 Accident preventing System in cutting Machine
ME335 Automatic Foot Dust Cleaning Machine
ME336 Fabrication of Power Generation from Kaplan turbine
ME337 Fabrication of Pneumatic ground driller
AUTOMATION AND MECHATRONICS BASED PROJECTS:-
AT001 90 degree Four Wheel turning Steering Mechanism
AT002 Automatic acceleration control in traffic signal for Two Wheeler
AT003 Pneumatic visual landing Gear with Automatic Tyre pressure inflation System for Aircraft
AT004 Eye blink sensor based Automatic Bumper and Breaking System
AT005 Automatic Idli batter filling Mechanism
AT006 Digital Automatic Tyre pressure inflation and monitoring System
AT007 Automatic railway track crack detecting Vehicle
AT008 Pneumatic Automatic Gear changer for Two Wheeler
AT009 Automatic Motorized Speed Breaker on time demand
AT010 Engine cooling and Fuel preheating System by using peltier element
AT011 Automatic Mirror adjustment System for Car by using Sensor
AT012 Automatic head light alignment with Automatic hand Brake System
AT013 Automatic PVC pipe feeding and cutting Machine
AT014 Fabrication of conveyor automation with dimension inspection
AT015 SMS based Pneumatic punching and Riveting Machine with Avoid Accident
AT016 Pneumatic controlled steps in Bus with Break locking System
AT017 Multi-purpose Agro Machine for Seed sowing with weed remover and fertilizer sprayer
AT018 Automatic Steering alignment System with Head light Dim/Bright controller
AT019 Electro-Magnetic Fuel conditioner for Two Wheeler with Load Test
AT020 Fabrication of Automatic foot board Break System for Car
AT021 Auto discharge Mechanism for Pneumatic punching Machine
AT022 Automation of Vibro cleaning process in a typical Die casting industry
AT023 Fuel Efficiency Increasing System by using Turbo Charger with Brake cooling System
AT024 Touch screen based Automatic Gear shifting System for Two Wheeler
AT025 Fuel Efficiency comparison of Air preheated System and Water injection System
AT026 Automatic Steer-by-wire Steering System for cars
AT027 Fabrication of Automatic conveyor based rice batching Machine
AT028 Cam shaft operated Automatic Gear change for Two Wheeler
AT029 Integrated automated Pneumatic jacks for Four Wheelers
AT030 Automatic Turbo charger at low and high Speed for Two Wheeler
AT031 Pneumatic disc Brake System by using Engine Exhaust gas
AT032 Automatic rubber tapping System from one tree to another tree
AT033 Automatic Brake failure detector and ignition locking System for Automobile
AT034 Intelligent active Suspension System for Two Wheeler
AT035 Automatic Pneumatic Cutting and grinding and shaping Machine
AT036 Solar auto charged grinding and Cutter Machine
AT037 Automatic Electro Hydraulic Jack for Four Wheeler
AT038 PLC based Automatic Pneumatic drilling Machine
AT039 Automatic Quick tool retrieval System for industry
AT040 Anti-theft Break locking with remote control System
AT041 Automatic Car Parking System for apartment Building
AT042 Hydraulic based Automatic emergency rescue ladder for fire Accident
AT043 SMS based Automatic Vehicle Accident information System
AT044 Automatic Riser removal in the casting by Pneumatic piston for foundry
AT045 Automatic Colour code sensing punching Machine
AT046 Digital lock Fuel pump & Break locking System for Two Wheeler
AT047 Safety System to avoid Accident when Driver in sleep
AT048 Automatic wall painting sprayer Machine
AT049 Over Speed Indication and Automatic Accident Avoiding System for two Wheeler
AT050 GPS based theft Vehicle Root tracking System
AT051 Automatic Ginger cutting, feeding and drying Machine
AT052 Automatic fire safety System for Fuel tank and Engine
AT053 Remote controlled Scrap collecting Vehicle
AT054 Automatic plastic separation module for municipal solid waste
AT055 Automatic air delivered System based on density of oxygen in Car cabin
AT056 Belt model based Stair climbing Wheel chair
AT057 Anti hijack System for Aero plane
AT058 Fabrication of safety added Pneumatic Cutting Machine
AT059 Automatic Differential unit Locking System
AT060 Fabrication of Multi-purpose Agri Cutter
AT061 Fabrication of Unaided Guided Vehicle (UGV)
AT062 Temperature monitoring System in cupola furnace
AT063 Fabrication of Automatic Stretch wrapping Machine
AT064  Anti-theft Wheel locking System with SMS alert
AT065 Punching Machine using width worth mechanism
AT066 Fabrication of Automatic Stroke therapy Chair
AT067 Automatic Side stand retriever System for Two Wheeler
AT068 Automatic scrap collecting & disposing Machine
AT069 Automatic Vehicle over load alert System
AT070 Wheel chair using Joystick and touch screen
AT071 Automatic drainage cleaning and detection of toxic gases
AT072 Queries controlling System for Two Wheeler
AT073 Fabrication of Multi-utility Agriculture Vehicle
AT074 Fully Automated potato Chip Slice making Machine
AT075 Automatic paper rolling and Pneumatic sealing Machine
AT076 Prevention kit for driving Two Wheeler without helmet
AT077 Foot operated plate cleaning Machine and dryer
AT078 Automatic Gear milling Machine using proximity sensor
AT079 Automatic weight Lifting jack with crank arrangement
AT080 SMS based Automated Guided Vehicle
AT081 Solar grass Cutting Machine
AT082 Automatic Pneumatic Bumper and Break actuation before collision
AT083 Fabrication of Automatic Street light controller
AT084 Automatic Car covering device For Automobile
AT085 Fabrication of Advanced Smart cradle with timer
AT086 Vehicle ignition using RFID and finger print Sensor
AT087 New high tech walking electric bike using solar power
AT088 Automatic boring mechanism for foundries
AT089 Fabrication of Automatic Pneumatic plastic crushing Machine
AT090 Automatic open well cleaning Machine
AT091 Automated Motorized dual acting CAN crusher
AT092 Automatic Gate open and close System using IR Sensor
AT093 Automatic Vehicle Accident Information System
AT094 Automated pet feeder for dog
AT095 Automatic safety Systems for railway coaches
AT096 Solar powered Water weed Cutter Machine
AT097 Automatic Pneumatic Gear shifting in Two Wheeler
AT098 Fabrication of potato peeling & slicing Machine
AT099 Fabrication of Quantity based sorting Machine
AT100 Fabrication of Automatic Motorized oil mill Mechanism
AT101 Automatic Break in hill station
AT102 Fabrication of pin on disc wear testing Machine
AT103 Automatic board cleaner with vacuum dust cleaner
AT104 Magnetic wall climbing Robot
AT105 Fabrication of Anti drown Vehicle
AT106 Automatic circle marker by play ground
AT107 Fabrication of Coin based shoe polishing Machine
AT108 PLC based Automatic Rotary Water Bottle filling System
AT109 Fabrication of Automatic multi-point grease Gun
AT110 Crane for multiple movements with holding Car and Lifting
AT111 Electronic Fuel Injection (EFI) System for Two Wheeler
AT112 Pedal cloth washing Machine with drier
AT113 Remote controlled Motorized Hydraulic jack
AT114 Automatic vertical Board cleaner
AT115 Anti-theft Steering System for Four Wheeler
AT116 Remote controlled Tilting fan
AT117 Neural control of a fully actuated biped Robot
AT118 Push operated Agriculture spray Pump for Garden
AT119 Fabrication of Automated gardener
AT120 Fabrication of Solar operated paddy Cutter
AT121 Fabrication of drainage cleaning Machine
AT122 Automatic side stands with Breaking locking System
AT123 Solar operated weed Cutter for Agriculture
AT124 Automatic Pneumatic emergency exit for Bus
AT125 Pre Drive Two Wheeler Authorization with Turbo on Demand
AT126 Auto roll punching Machine using Geneva mechanism
AT127 Magnetic levitation Flight/Train landing System
AT128 Automatic convertible Wheel Chair cum bed
AT129 Automatic Packing control Machine
AT130 Electrical energy produce by Vibration by using Foot step method
AT131 Motorized 3 axis Electro chemical drilling Machine
AT132 Design & Development of standing Wheel Chair
AT133 Automatic Vehicle Accident prevention System
AT134 Digital Hydraulic spring testing Machine
AT135 Sensor Based Automatic Water level Sensing Crane
AT136 Motorized Pipe Cutting Machine using Quick Return Mechanism
AT137 Integrated drunk and drive prevention System
AT138 Semi-Automatic feeding Mechanism for small scale Poultry farm
AT139 Automatic Tyre Pressure Inflation System
AT140 Fabrication of Button operated Pneumatic Railway Track changer
AT141 Wireless Joystick operated tool post for lathe
AT142 Power Generation in highway using fast moving Vehicle
AT143 Accident Avoiding System for Punching Machine
AT144 Fabrication of Electric bike with Gear transmission
AT145 Fabrication of Automatic punching/Printing conveyor
AT146 Automatic Water over flow controlling System
AT147 Pneumatic Auto feed Drilling Machine
AT148 Semi-Automatic Water tank cleaner
AT149 Automatic Pneumatic Speed Breaker with day and night control
AT150 An optical method of Foot pressure monitoring & therapy for paralyzed patient
AT151 Automatic Voice controller Wheel Chair
AT152 Power Generation from sea Water by MHD Power Generation method
AT153 Joystick control Wheel chair for physically challenged people
AT154 Advanced emergency Braking System
AT155 Fabrication of Pneumatic Auto Gear changer
AT156 Fabrication of Motorized Agri Cutter
AT157 Inspection Conveyor for quality control
AT158 Solar grass Cutter with Water spraying System
AT159 Coconut tree climbing and cutting Machine
AT160 Air Compressor using Quick return Mechanism
AT161 Fabrication of Airbag Automation
AT162 Reduction Power cost in induction furnace by alarm & Sensor System
AT163 Automatic Electro Hydraulic Braking System
AT164 Fabrication of Motorized shaper and slotter in a single Machine
AT165 Sensor Operated Fire Fighting AGV
AT166 Automatic Brake failure indicator with Automatic Braking by Electromagnet coil
AT167 Sensor Based Inspection Conveyor
AT168 Multiple Power Generation from Solar energy, Wind mill and rain water
AT169 Fabrication of Pneumatic garage door opener
AT170 Automobile Exhaust heat Refrigeration System
AT171 Fabrication of Three axis CNC milling Machine
AT172 Fabrication of Geneva conveyer with Pneumatic pin punch
AT173 High efficient cooling System with help of BLDC motor
AT174 Motorized head light adjustment in Two Wheeler
AT175 Automatic Motorized Four Wheel Steering Mechanism
AT176 Automatic digital Tyre pressure inflation and deflation System
AT177 Automatic Double Axis Welding Machine
AT178 Advanced Automatic pumping System for Agriculture using soil Sensor
AT179 Fabrication of Hydraulic sensing cutting Machine
AT180 Boiler automation with Digital steam Power plant
AT181 Fabrication of Remote operated weapon System
AT182 Fabrication of Exo-support for legs
AT183 Auto Indexing Gear cutting attachment for Pneumatic shaping Machine
AT184 Fabrication of nut inspection conveyor
AT185 Multi tasked smart Wheel chair for physically challenged people
AT186 Automatic Sheet metal feeding & Cutting Machine
AT187 Automatic Vehicle over Speed controlling System for School Zone
AT188 Fabrication of 360 degree parking assistance System
AT189 Automatic multi axis CNC drilling Machine
AT190 Automatic drunken Drive avoiding with Helmet locking System
AT191 Automation to finding the life time of switches
AT192 Fabrication of Anti-lock Braking System (ABS)
AT193 Automatic Object detection and Vibration alert to blind people
AT194 Electro Hydraulic System for Automation in Vehicle
AT195 Automatic medicine dispenser for sugar patient
AT196 Hydraulic parking attachment in Car
AT197 Fabrication of Automatic T-Shirt folding Machine
AT198 Automatic work piece counting with belt conveyer
AT199 Fabrication of Rotary smart car parking System
AT200 Fabrication of Automatic Pneumatic Printing Press
AT201 Fabrication of Starter Motor over running prevention
AT202 Remote operated wireless crane control System
AT203 Design & Fabrication of Solar Street light with day night control
AT204 Automatic Speed Breaker for preventing Accident in school zone
AT205 Combined model of Automatic head light dim / bright System and Automatic hand Break release System
AT206 Sensor Operated Automatic Ramming Machine
AT207 Surface finish measuring equipment with digital display
AT208 Electronic assisted Hydraulic Braking System
AT209 Fabrication of vertical Lift Mechanism for Kattwyk Bridge
AT210 Automatic double axis Pneumatic JCB Equipment
AT211 Solar powered Peltier Car cabin cooling System
AT212 Mechanical can crusher with Automatic feeding mechanism
AT213 Seat belt based ignition System for Car
AT214 Fabrication of Button operated Hydraulic jack
AT215 Fabrication of Parallel Car parking System
AT216 Sensor Operated Automated Guided Vehicle (AGV)
AT217 Automatic spring de-coiler Machine
AT218 Automatic Steering control System for Automobile
AT219 Fabrication of Agricultural Robot
AT220 Fabrication of Multi safety System in bumper
AT221 Automatic hand Brake System by using Pneumatic interface
AT222 GSM Based Two Wheeler security System
AT223 Easy Car parking System by 90 degree Steering Mechanism
AT224 Highways high Speed sensing and Automatic Pneumatic Braking System
AT225 Fully covered Two Wheeler with Automatic extra Wheel balancing System
AT226 Automatic chocolate punching Machine
AT227 Fabrication of Sound based fire extinguisher
AT228 Semi automated wall plastering Machine
AT229 Automatic drip Irrigation for precision Agriculture
AT230 Sensor Operated Foot dust cleaner
AT231 Automatic weighing and sealing Machine
AT232 Automatic Spring End Grinding Machine
AT233 Fabrication of pedal operated Hacksaw with mobile charge
AT234 Automobile dual side wiper System with mist control
AT235 Automatic Lifting Vehicle inbuilt attached jack
AT236 Automatic over load indication for bridge
AT237 Chip and dust collecting Vehicle by using Blower
AT238 Automatic Rain sensing window for Home/Car
AT239 Six leg Robot for Agriculture purpose which can spray Seed and water
AT240 Fabrication of Automatic Fault egg sorting Machine
AT241 Electro-Magnetic scrap collecting Vehicle
AT242 Design & Fabrication of Conveyor Automation
AT243 Fitness equipment for localized electrical Power Generation
AT244 Automatic Car washing System by using IR Sensor
AT245 Semi-Automatic transfer Machine in conventional industries
AT246 Pneumatic Bumper and Breaking with head light dim & bright controller
AT247 Pedal operated Solar Cell phone Charger
AT248 Pedal operated wet grinder with Cell phone charger
AT249 Multi-purpose Pneumatic Sheet Cutting and Sheet bending Machine
AT250 Automatic Humidification System
AT251 Solar operated portable vacuum cleaner
AT252 Remote controlled handicapped Wheel chair cum bed
AT253 Blue tooth operated Mechanical arm
AT254 Tread mill Bicycle with Power Generation
AT255 Combination of emergency, intelligence and anti-lock Braking System
AT256 Portable coin shorter Machine
AT257 Automatic Fire fighting cum material handling Vehicle
AT258 Generation of electricity from cycling exercise
AT259 Automatic Rain operated wiper and Head light Dim / Bright Controller
AT260 Automatic Motorized Centre stand for Two Wheeler
AT261 Fabrication of Automatic Railway Gate Controller
AT262 Button operated Motorized portable mini crane
AT263 Automatic Book Reading aid for handicapped People
AT264 Fabrication of harvesting Seed putting & threshing Machine
AT265 Automated prosthetic leg for physically challenged
AT266 Solar operated Automatic Seed Sowing Machine
AT267 Automatic Foot Dust Cleaning Machine
AT268 Semi-autonomous Multi-purpose cleaning Vehicle
AT269 Automated paper cup Feeding and making Machine
AT270 Automatic Electromagnetic retarder System using Ultrasonic waves
AT271 Automatic Car window opening by using sound & oxygen sensor
AT272 Automatic Agar Bhatti stick counting Machine
AT273 Shaft Driver Bicycle with 2 Speed Automatic Gear transmission System
AT274 Solar grass Cutter with Automatic sun tracking System
AT275 Automatic paper cutting using Geneva mechanism
AT276 Step climber Wheel chair by planetary Gear mechanism
AT277 MPPT control strategy for Wind energy conversion System
AT278 Semi Automated Areca Nut / Coconut Collecting conveyor
AT279 Automatic Paint Spraying Equipment
AT280 Fabrication of Automatic sweeping Vehicle
AT281 Automatic multi directional photo shearing Machine
AT282 Automatic emergency exit and tyre inflation System
AT283 Fabrication of smart bike
AT284 Automatic Speed Breaker depending upon Vehicle over Speed
AT285 Modified Accident prevention crash guard by using Sensor
AT286 Automatic portable groundnut planting Machine
AT287 Fabrication of Intelligent Braking System (IBS)
AT288 Automatic Agar Bhatti incense stick counting and packing Machine
AT289 Conveyor for Dimension Rejection System
AT290 Automation in diode assembly for industry automation
AT291 Button operated Pneumatic Gear shifting System for Two Wheeler
AT292 SMS punching and riveting with Accident avoiding System
AT293 Automatic grass cutting by using Sensor
AT294 Anti dazzling head light for Two Wheeler
AT295 Motorized screw jack with Solar panel and lighting System
AT296 Automatic Engine oil alerting System
AT297 Semi-Automatic Road Reflector Stud Installation Machine
AT298 Fabrication of Unpowered exoskeleton boot
AT299 Automatic Dish Washing Machine with dryer
AT300 Pneumatic Hacksaw Machine with shaping attachment
AT301 Semi-Automatic Weed Remover in Sugarcane Farm
AT302 Pedal operated Washing Machine for Cloth
AT303 Double axis drilling Machine
AT304 Smart cane (Stick) for visually impaired people
AT305 Automatic scrap Compression Machine
AT306 Digital locking System (Password) for Two Wheeler
AT307 Automatic Gear changer in Bicycle
AT308 Automatic parking and Breaking System
AT309 Fabrication of Pneumatic Power Generation
AT310 Automatic Dosa making Machine
AT311 Fabrication of Motorized Embossing drilling Machine
AT312 Automatic Shoe polisher Machine with coin box
AT313 Fabrication of Motorized Three axis crane
AT314 Automatic Distance Measurement and Braking System By using Ultrasonic Waves
AT315 Intelligent trolley for domestic cylinder
AT316 Button operated Hydraulic jack
AT317 Fabrication of Pneumatic conveyor
AT318 Remote control Car covering System
AT319 Two Wheeler Automation with security System
AT320 Pneumatic CAN crusher with Automatic feed Mechanism
THERMAL (AND) REFRIGERATION & A/C BASED PROJECTS:-
TH001 Fabrication of Turbojet Engine with Active Magnetic Bearing
TH002 Cold start Performance enhancement of Motor with Cycle catalytic converter using latent heat storage System
TH003 Electro-Magnetic Fuel conditioner of Two Wheeler with Load Test
TH004 Increasing the Efficiency of Turbo Charger during low Engine Speed by turbo-lag reduction
TH005 Experimental study and testing of Solar flat plate collector with concrete and adjustable glass cover
TH006 Experimental study and application of Nano fluid in Refrigeration
TH007 Heat dissipation in cars using thermo electric Refrigeration
TH008 Enhancing performance of IC Petrol Engine by Peltier Air preheating System along with Exhaust Gas heat recovery System
TH009 Power Generation and Refrigeration by using waste heat from IC Engine
TH010 Automobile Exhaust heat Refrigeration System
TH011 Performance analysis of Solar Water Heater using porous medium and Agitator
TH012 Boiler automation with Digital steam Power plant
TH013 Performance analysis of single slope Solar still with biomass and jute separately
TH014 Fabrication for converting waste plastic to Bio diesel Fuel
TH015 Experimental investigation of an Air Conditioning System drive by Engine
TH016 Fabrication of Hybrid Water Heater with Air dryer
TH017 Pyro electric energy harvesting from Solar and Wind energy
TH018 Salt Water purification and electricity production from steam Power plant
TH019 Experimental study on single basin Solar still augmented with biomass Water Heater
TH020 Fuel Efficiency comparison of Air preheated System and Water injection System
TH021 Two Wheeler Engine cooling and Fuel preheating using peltier element
TH022 Effect of Controlling Parameters on Heat Transfer during Jet Array Impingement Cooling of a Hot Steel Plate
TH023 Fabrication of LPG Refrigeration with PCM
TH024 Experimental setup and Application of Nano fluid in Solar Water Heater
TH025 Design and development of downdraft Gasifier for operating CI Engine on dual Fuel mode
TH026 Fabrication of Electrical energy production from Waste oil burning System
TH027 Fabrication and Experimental study of shell and Tube heat exchanger
TH028 Fabrication of Solar Air Dryer
TH029 Automatic Air delivery System based on density of oxygen in Car cabin
TH030 Diesel blended with Hydrogen Engine
TH031 Sea Water converted to RO drinking Water by using Solar Power
TH032 Fabrication of Catalytic converter with PCM
TH033 Combined Economic and Power mode by using super Charger and Hydrogen Fuel
TH034 Fabrication and performance test of a model Solar Refrigeration System
TH035 Fabrication of storage type Water cooler
TH036 Fabrication of Three in one Air Conditioner
TH037 Efficiency monitoring of a two Stroke Petrol Engine by using Air heat exchanger
TH038 Effect of Nano Fluid in a modified vacuum single basin Solar still
TH039 Fabrication and analysis of micro channel heat exchanger
TH040 Experimental study on the performance of heat pump System trans-critical carbon Di-oxide (CO2) refrigerant
TH041 Fabrication of pressure vessel heat exchanger
TH042 Experimental study of heat transfer enhancement in liquid piston cylinder
TH043 Experimental study of downdraft Gasifier & nozzle optimization
TH044 Fabrication of Solar peltier Air Conditioner
TH045 Performance analysis of evaporative air cooled condenser
TH046 Advance cooling System in a tourist Bus
TH047 Reduction Power cost in induction furnace by alarm & Sensor System
TH048 Intelligent solar-powered Automobile ventilation System
TH049 Increasing the Efficiency of Vehicle at higher altitude with Load Test
TH050 Fabrication of cooling jacket for Motorcycle
TH051 Automatic Transformer heat reduction System
TH052 Pulsating heat pipe based heat exchangers
TH053 Fabrication and experimental study of Air Condition trainer kit
TH054 Fabrication of Thermo acoustic Refrigeration System
TH055 Solar plus Compressor Heat Desalination Water Still
TH056 Fabrication of Water Cooler cum Air Conditioner
TH057 Experimental study of Refrigeration setup with two Different Diffusers
TH058 Fabrication of Solar Air Conditioner
TH059 Extraction of mercury from CFL waste
TH060 Water cooler cum Water Heater by using Refrigeration System
TH061 Solar enhanced energy efficient food processor
TH062 Generation of Power using municipal social waste
TH063 Fabrication of Solar room warmer
TH064 Fabrication of Osmotic power plant
TH065 Fabrication of Automatic humidification System
TH066 Fabrication of Solar stored cook stove
TH067 Solar Air Cooler cum Heater with auto tracking System
TH068 VIVACE (vortex induced vibration aquatic clean energy) a new concept in generation of clean and renewable energy from fluid flow
TH069 Fabrication of Peltier air cooler cum Heater
TH070 Fabrication of Solar Fridge
TH071 Solar powered Peltier Car cabin cooling System
TH072 Fabrication of Hybrid titanium Air Conditioner
TH073 Design & Fabrication of combo Refrigerator
TH074 Power Generation from sea Water by MHD Power Generation method
TH075 Improved energy performance of a Refrigerating Machine using Water spray upstream of the Condenser
TH076 Experimental analysis of solid desiccant Wheel dehumidifier
TH077 Pedal powered reverse osmosis Water purification
TH078 Indirect type solar dryer integrated with Solar air Heater
TH079 Fabrication of bomb calorimeter
TH080 Fabrication of Portable juice cooler
TH081 Advanced Solar Water Heater with Electricity Generation
TH082 Solar cabinet drier integrated with biomass
TH083 Fuel Efficiency Increasing System by using Turbo Charger with Brake cooling System
TH084 Automatic temperature controller with cooling System
TH085 Fabrication of combustion chamber for rocket Engine
TH086 Design & Fabrication of Water dispenser cum Air Conditioner
TH087 Regenerative Compressed air System by suspension for Automatic Turbo lag reduction
TH088 Low pressure Solar Water Heater with Auto tracking
TH089 Fabrication of EGR assisted jet Compressor
TH090 Three methods of emission and Efficiency comparison- Petrol Engine, acetylene mixed with LPG and Petrol mixed with acetylene
TH091 Parametric study on the thermal performance of the Solar air Heater with energy storage
TH092 Fabrication of Lube oil cooler
TH093 Portable steam generator with Iron box
TH094 Working of Air Conditional unit using damping effect of shock absorber
TH095 Fabrication of Vapour Compression distillation
TH096 Fabrication of LPG Refrigeration
TH097 Fabrication of pollution free Four Stroke Petrol Engine
TH098 Fabrication of Hot and Cold Water Dispenser
TH099 Fabrication of Solar oven
TH100 Super charging an Engine using Vehicle suspension
TH101 Air preheating System using condenser waste heat in Automobile
TH102 Fabrication of briquette burner
TH103 Air Conditioning of an Automobile using Engine Exhaust gas
TH104 Fabrication of thermal storage unit using PCM
TH105 Fabrication of Ground Dryer
TH106 Fabrication of magnetic Fuel modifier in Diesel Engine with Water injection
TH107 Solar Water Desalination by using photovoltaic method
TH108 Fabrication of Life time kit for an Air Conditioning
TH109 Air purification using Electrostatic plate and coupled with Dehumidifier
TH110 Design and analysis of Aero spike nozzle for an air augmented rocket Engine
TH111 Fabrication of Furnace using infrared Lamp
TH112 Introduction to the revolutionary design of Schaffer reflectors
TH113 Energy conservation in steam Power Plant
TH114 Design & Fabrication of atmosphere cooling tower
TH115 Fabrication of Magnetic Fuel Modifier used in IC Engine
TH116 Optimization of process parameters in spark EDM
TH117 Solar thermo-electric Refrigerator
TH118 Design and Fabrication of friction stir welding Machine
TH119 Fabrication of plate freezer
TH120 Fabrication of Solar still coupled with Air Conditioner
TH121 Experimental study of multiple tray solar desalination
TH122 Fabrication of Mini Jet Engine
TH123 Fabrication of Vortex flow floating turbine
TH124 Refrigerant Cycle & thermo state expansion valve System
TH125 Magneto Rheological Fluid (MRF) Breaking System
TH126 Experimental study of control parameter in spray cooling in a hot steel plate
TH127 Design and development of natural vegetables/fruits Preservator
TH128 Fabrication of Exhaust Gas Power Generation by Blower
TH129 Fabrication of Miniature Boiler
TH130 Experimental investigation Solar Pond integrated with PCM storage
TH131 Fabrication of pin on disc wear testing Machine
TH132 Fabrication of heat exchanger for store thermal energy using PCM
TH133 Experimental setup on Gasifier
TH134 Fabrication of Latent Heat Exchanger
TH135 Automation of Vibro cleaning process in a typical die casting industry
TH136 Electrical Power Generation using Thermal Power Plant
TH137 Fabrication of cooling tower
TH138 Temperature monitoring System in cupola furnace
TH139 Multi-Purpose Ground Dryer (or) Multi-Purpose Dryer Cum Room Heater
TH140 Industrial vacuum conveyor for biscuit dryer
TH141 Fabrication of Cryogenic Engine using liquid nitrogen
TH142 Fabrication and Experimental study of Refrigeration Trainer kit
TH143 Thermo-electric Solar Air Conditioner
TH144 Fabrication of Bicycle powered Refrigerator
TH145 Fabrication of Solar absorption Air Conditioner
TH146 Fabrication of Aluminium Extraction from plastic material
TH147 Electrical Power Generation System by using Gasifier
TH148 Fabrication of twisted tape heat exchanger
TH149 Pollution free Miniature incinerator
TH150 Fabrication of Solar dryer with multiple PCM
TH151 Nano Fluid based solar desalination using flashing technique
TH152 Reflecting mirror type solar steam generator
TH153 Fabrication of Mist Coolant System
TH154 Waste chill recovery heat exchange
TH155 PV panel cooling using stack effect
TH156 Experimental study of Refrigeration System using carbon Di-oxide (co2) Refrigerant
TH157 Cyclone separator with blower
TH158 Fabrication of Four in one Air Conditioner
TH159 Design and performance of a vacuum single basin Solar still
TH160 Working of Air Conditioning unit using damping effect of shock absorbers
TH161 Fabrication of laminar flow Water turbine
TH162 Development of basin solar still by adding magnetic treatment unit and double glass cover provided with Water
TH163 Fabrication of Refrigeration using waste heats in Car
TH164 Fabrication of Loop heat pipe
TH165 Fabrication of MHD Power Generation from sea water
TH166 Parabolic Trough collector cum Vapor Adsorption Refrigerator
TH167 Design, Fabrication and heat transfer study of greenhouse dryer
TH168 Fabrication of Steam jet Refrigeration
TH169 Fabrication of biomass briquetting Machine
TH170 Solar aided portable vacuum desalination plant
TH171 Fabrication of Bottle Cooler
TH172 Fabrication of Solar Air Cooler cum Heater
TH173 Bio-Diesel extraction from waste plastic material
TH174 Heating and cooling jacket by using peltier effect
TH175 High efficient cooling System with help of BLDC motor
TH176 Solar powered Electrolux Refrigeration System
TH177 Remote controlled boiler flame adjustment System
DESIGN & FABRICATION AND EXPERIMENTAL STUDY BASED PROJECTS:-
DF001 Fabrication and experimental study of Opposite Piston Opposite Cylinder (OPOC) Engine
DF002 Experimental study and Application in Nano Fluid in Refrigeration
DF003 Fabrication and experimental study of Increasing the Efficiency of Vehicle at higher altitude with Load Test
DF004 Fabrication and experimental study of Single state double acting cylinder using electromagnet reciprocating pump
DF005 Fabrication and experimental study of Air Condition trainer kit
DF006 Fabrication and experimental study of Solar dryer with multiple PCM
DF007 Fabrication and experimental study of Solar powered Peltier Car cabin cooling System
DF008 Experimental study of Refrigeration setup with two different diffusers
DF009 Fabrication and experimental study of Electrode flux removing Machine
DF010 Fabrication and experimental study of solar cabinet drier integrated with biomass
DF011 Fabrication and experimental study of Salt Water purification and electricity production from steam Power plant
DF012 Experimental setup and Application of Nano Fluid in Solar Water Heater
DF013 Fabrication and experimental study of 90 degree four Wheel turning Steering Mechanism
DF014 Fabrication and experimental study of Tread mill Bicycle with Power Generation
DF015 Effect of Controlling Parameters on Heat Transfer during Jet Array Impingement Cooling of a Hot Steel Plate
DF016 Fabrication and experimental study of Fuel Efficiency comparison of Air preheated System and Water injection System
DF017 Fabrication and experimental study of Combined Economic and Power mode by using super Charger and Hydrogen Fuel
DF018 Fabrication and experimental study of Magneto Rheological Fluid (MRF) Braking System
DF019 Fabrication and experimental study of T- box Wind Mill
DF020 Enhancing performance of IC Petrol Engine by Peltier Air preheating System along with Exhaust Gas heat recovery System
DF021 Fabrication and experimental study of Super charging an Engine using Vehicle suspension
DF022 Performance analysis of single and dual slope Solar still with biomass and jute separator
DF023 Fabrication and experimental study of Hydrogen and Petrol mixed Engine
DF024 Fabrication and experimental study of magnetic Fuel modifier in Diesel Engine with Water injection
DF025 Fabrication and experimental study of Motorized Coconut Dehusking Machine
DF026 Fabrication and experimental study of Energy-harvesting shock absorber with a mechanical motion rectifier
DF027 Fabrication and experimental study of friction stir welding Machine
DF028 Fabrication and experimental study of Effect of CNT addition on MR fluid damper
DF029 Fabrication and experimental study of Cryogenic Engine using liquid nitrogen
DF030 Fabrication and experimental study of Turbo charged Two Wheeler with zero Turbo lag
DF031 Design & Fabrication of Riser Removal in the casting pieces by Pneumatic piston
DF032 Fabrication and experimental study of twisted tape insert in heat exchanger
DF033 Fabrication and experimental study of conveyor automation with dimension inspection
DF034 Optimization of process parameters in spark EDM
DF035 Fabrication and experimental study of Automation of Vibro cleaning process in a typical Die casting industry
DF036 Fabrication and experimental study of Automobile suspension made of Hydraulic magneto rheological damper
DF037 Fabrication and experimental study of Floating Wind turbine
DF038 Fabrication and experimental study of EGR assisted jet Compressor
DF039 Fabrication and experimental study of potato peeling & slicing Machine
DF040 Fabrication and experimental study of Pyro Electric energy harvesting from Solar and Wind energy
DF041 Fabrication and experimental study of double side Hack saw Cutting Machine
DF042 Experimental study and testing of Solar flat plate collector with concrete and adjustable glass cover
DF043 Fabrication and experimental study of pin on disc wear testing Machine
DF044 Fabrication and experimental study of Regenerative Compressed air System by suspension for Automatic Turbo lag reduction
DF045 Fabrication and experimental study of Pre Drive Two Wheeler Authorization with Turbo on Demand
DF046 Fabrication and experimental study of Semi active suspension System
DF047 Experimental investigation & comparative study of Diesel Engine Fuelled with used transformer oil with Ethanol
DF048 Optimization and testing of Automobile radiator
DF049 Fabrication and experimental study of Cold start Performance enhancement of Motor with Cycle catalytic converter using latent heat storage System
DF050 Fabrication and Experimental study of Micro channel heat exchanger
DF051 Fabrication and experimental study of Magnetic Fuel Modifier used in IC Engine
DF052 Fabrication and experimental study of Electro-Magnetic Fuel conditioner with Load Test
DF053 Fabrication and experimental study of Ferro fluid Power Generation
DF054 Experimental study of heat transfer enhancement in Liquid Piston Cylinder
DF055 Generation of electricity from ocean waves using rack and pinion mechanism
DF056 Fabrication and experimental study of Auto discharge Mechanism for Pneumatic punching Machine
DF057 Experimental study of Downdraft Gasifier with Nozzle optimization
DF058 Fabrication and experimental study of Air bag System for Two Wheeler
DF059 Fabrication and experimental study of Air preheating System using condenser waste heat in Automobile
DF060 Fabrication and experimental study of Extraction of mercury from CFL waste
DF061 Fabrication and experimental study of Energy conversion from Roadways using kinetic motion
DF062 Design and Fabrication of Punching Machine using scotch yoke Mechanism
DF063 Experimental study of Refrigeration System using carbon Di-oxide (co2) Refrigerant
DF064 Fabrication and experimental study of Solar room warmer
DF065 Fabrication and experimental study of Surface finish measuring equipment with digital display
DF066 Fabrication and experimental study of Air Conditioning of Automobile using Engine Exhaust gas
DF067 Fabrication and experimental study of bomb calorimeter
DF068 Fabrication and experimental study of Heat dissipation in cars using thermo electric Refrigeration
DF069 Fabrication and experimental study of Magneto rheological clutch with Load Test
DF070 Fabrication and experimental study of LPG Refrigeration with PCM
DF071 Fabrication and experimental study of Deflection of beam apparatus
DF072 Fabrication and experimental study of tool cutting force of dynamo meter on lathe
DF073 Fabrication and experimental study of Increasing the Efficiency of Turbo Charger during low Engine Speed by turbo-lag reduction
DF074 Fabrication and experimental study of Diffuser Type Hybrid Wind turbine
DF075 VIVACE (vortex induced vibration aquatic clean energy) a new concept in generation of clean and renewable energy from fluid flow
DF076 Fabrication and experimental study of Air brake System using Engine Exhaust gas
DF077 Fabrication and experimental study of V-through special type Solar Water Heater
DF078 Fabrication and Application of evaporation air cooler coupled with Solar Water Heater for dehumidification of indoor air
DF079 Fabrication and experimental study of LPG Refrigeration System
DF080 Fabrication and experimental study of Inbuilt Hydraulic jack coupled with Engine for Four Wheeler
DF081 Fabrication and experimental study of Darrieus rotor Wind turbine
DF082 Fabrication and experimental study of Working of Air Conditional unit using damping effect of shock absorber
DF083 Enhancing the IC Engine Performance by Using the Electrolysis and Preheating Process
DF084 Development of Homogeneous charge Compression ignition (HCCI) Engine on electric motor Cycle
DF085 Fabrication and experimental study of three methods of emission and Efficiency comparison- Petrol Engine, Acetylene mixed with LPG and Petrol mixed with Acetylene
DF086 Fabrication and Detection of cavitation’s in venture injector using strain gauges
DF087 Fabrication and experimental study of Fuel Efficiency Increasing System by using Turbo Charger with Brake cooling System
DF088 Fabrication and Experimental setup on Gasifier
DF089 Fabrication and study of heat exchanger for store thermal energy using PCM
DF090 Fabrication and experimental study of Diesel blended with Hydrogen Engine
DF091 Experimental analysis of Solar Water Heater using porous medium and agitator
DF092 Fabrication and experimental study of Efficiency monitoring of a two Stroke Petrol Engine by using Air heat exchanger
DF093 Working of Air Conditioning unit using damping effect of shock absorbers
DF094 Fabrication and experimental study of Automobile Exhaust heat Refrigeration System
DF095 Effect of swirl induction by internally threaded inlet manifolds on Exhaust emissions of single cylinder Diesel Engine
DF096 Fabrication and experimental study of bottle cooler
DF097 Fabrication and experimental study of Power Generation from Kaplan turbine
DF098 Fabrication and experimental study of Non-Conventional Method of Water Pumping Using Vertical Wind Turbine
DF099 Fabrication and experimental study of Refrigeration trainer kit
DF100 Improved energy performance of a Refrigerating Machine using Water spray upstream of the Condenser
DF101 Fabrication and experimental study of Power Generation from Francis turbine
DF102 Fabrication and Performance analysis of evaporative air cooled condenser
DF103 Fabrication of Smart energy monitoring Break over module
DF104 Fabrication and experimental study of Multiple Power Generation from Solar energy, Wind mill and rain water
DF105 Fabrication and experimental study of Reflecting mirror type solar steam generator
DF106 Fabrication and performance test of a model Solar Refrigeration System
DF107 Fabrication and experimental study of two stage Mechanical Water pendulum oscillator
DF108 Fabrication and experimental study of Bladeless Turbine with Propeller
DF109 Fabrication and experimental study of Turbojet Engine with active magnetic bearing
DF110 Fabrication and experimental study of Steam jet Refrigeration
DF111 Effect of controlling parameters on heat transfer during spray impingement cooling of steel plate
DF112 Fabrication and experimental study of semi-Automatic feeding Mechanism for small scale Poultry farm
DF113 Fabrication and experimental study of combo Refrigerator
DF114 Fabrication and experimental study of multipurpose agricultural Vehicle
DF115 Fabrication and experimental study of Hydro-Pneumatic Moving Vehicle
DF116 Fabrication and experimental study of electromagnetic Moulding Machine
DF117 Design and analysis of Aero spike nozzle for an air augmented rocket Engine
DF118 Fabrication and experimental study of Thermo electric Refrigerator
DF119 Fabrication and experimental study of Vortex flow floating turbine
DF120 Fabrication and experimental study of Peltier Air Cooler cum Heater
DF121 Fabrication and experimental study of Cryogenic liquid nitrogen as a Fuel for zero emission Vehicle
DF122 Fabrication and experimental study of Nano Fluid based solar desalination using flashing technique
DF123 Fabrication and experimental study of Magneto Rheological Damper
DF124 Fabrication and experimental study of automated paper cup Feeding and making Machine
DF125 Fabrication and experimental study of solar peltier Air Conditioner
DF126 Fabrication and experimental study of vertical dual rotor Wind turbine
DF127 Fabrication and experimental study of Advanced Solar Water Heater with Electricity Generation
DF128 Optional acceleration circuit to increase the Fuel Efficiency of single cylinder Petrol Engine by double carburetor method
DF129 Fabrication and experimental study of multiple tray solar desalination
NON-CONVENTIONAL BASED PROJECTS:-
MN001 Tread mill Bicycle with Power Generation
MN002 Experimental analysis of solar powered ventilation coupled with thermo electric generator on unroofed parked Vehicle
MN003 Automobile Two Wheeler Exhaust heat Refrigeration System
MN004 Kinetic Energy Recovery System (KERS) Cycle
MN005 Salt Water purification and electricity production from steam Power plant
MN006 VIVACE (vortex induced vibration aquatic clean energy) a new concept in generation of clean and renewable energy from fluid flow
MN007 Power Generation from Speed Breaker by using Hydraulic System
MN008 Experimental setup and Application of Nano fluid in Solar Water Heater
MN009 Pedal cloth washing Machine with Drier
MN010 Performance analysis of dual slope Solar still with biomass and jute separately
MN011 Super charging an Engine using Vehicle suspension
MN012 Conversation of sea Water into drinking Water using Solar panel
MN013 Electrical Power Generation by Road hump
MN014 Pyro electric energy harvesting from Solar and Wind energy
MN015 Fabrication of vertical Dual Rotor Wind Turbine
MN016 Experimental study and testing of Solar flat plate collector with concrete and adjustable glass cover
MN017 Belt model based solar stair climbing Wheel chair
MN018 Agricultural Paddy cutting and weed cutting by using Solar Power
MN019 Hydro Power plant with salt Water purification System
MN020 Dual Axis Automatic Solar panel Tracking System
MN021 Solar grass Cutter with Automatic Sun Tracking System
MN022 Development of a Soft Robotic Arm Gripper Using a Micro Pump
MN023 Power Generation from sea Water by MHD Power Generation method
MN024 Indirect type solar dryer integrated with Solar air Heater
MN025 Remote controlled Solar powered handicapped tilting Wheel chair
MN026 Design and Fabrication of helical type vertical axis Wind turbine
MN027 Compressed air generated using Speed Breaker
MN028 Fabrication of Agricultural model pump
MN029 Power Generation from organic waste of college canteen
MN030 Solar still with and without external magnetic treatment
MN031 Pedal operated Washing Machine for Cloth
MN032 Fabrication of Buggy with Solar Hybrid Vehicle
MN033 Fabrication of Steam Operated Flame Gulping Engine
MN034 Solar trough collector with auto tracking
MN035 Energy-harvesting shock absorber with a mechanical motion rectifier
MN036 Electrical Power production and Water pumping from Speed Breaker
MN037 Fabrication of Mobile charging from shoe
MN038 Fabrication of Fuel cell bike
MN039 Motorized screw jack with Solar panel and lighting System
MN040 Fabrication of Tilting Three wheeler with a Hybrid System
MN041 Fabrication of Solar oven
MN042 Solar still coupled with Air Conditioner
MN043 Fabrication for converting waste plastic to Fuel
MN044 Fabrication of Solar absorption Air Conditioner
MN045 Experimental study of multiple tray solar desalination
MN046 Solar cabinet drier integrated with biomass
MN047 Electric scooter powered by Wind & Piezo Electric power
MN048 Fabrication of tunnel type Solar still
MN049 Solar powered Peltier Car cabin cooling System
MN050 Fabrication of Solar Hybrid Car
MN051 Regenerative Braking System using Pneumatic interface
MN052 Fabrication of Floating Wind turbine
MN053 Experimental study on single basin Solar still augmented with biomass Water Heater
MN054 Parametric study on the thermal performance of the Solar air Heater with energy storage
MN055 Electrical Power Generation from Speed Breaker using roller Mechanism
MN056 Electrical Power Generation from mini Hydro Power plant
MN057 Performance evaluation of solar air collector with transpired absorber and cover
MN058 Solar plus Compressor Heat Desalination Water Still
MN059 Fabrication of Solar electric regenerative Cycle
MN060 Fabrication of Solar Race Car
MN061 Fabrication of Solar E Cycle
MN062 Application of evaporation air cooler coupled with Solar Water Heater for dehumidification of indoor air
MN063 Fabrication of Solar Automatic Step Climber
MN064 Fabrication of Solar wood Cutting Machine
MN065 Solar enhanced energy efficient food processor
MN066 Solar Powered Automatic Rain Operated Wiper
MN067 Generation of electricity from ocean waves using rack and pinion mechanism
MN068 Solar powered Water weed Cutter Machine
MN069 Pollution free Miniature incinerator
MN070 Basin type Solar still multiple floating porous absorbers
MN071 Generation of Power using municipal Social Waste
MN072 Solar Seed Dryer with Auto tracking
MN073 Fabrication of Solar sterling Engine (Model)
MN074 Fabrication of Air powered Cycle
MN075 PV panel cooling using stack effect
MN076 Fabrication of Double Effecting Solar Cooker
MN077 Pedal Operated Solar cell phone charger
MN078 Two stage Mechanical Water pendulum oscillator
MN079 Fabrication of Solar Car lift jack
MN080 Electrical Power Generation System using Railway track
MN081 Solar operated portable Vacuum Cleaner
MN082 Fabrication of Solar stored cook stove
MN083 Fitness equipment for localized electric Power Generation
MN084 Fabrication of paddling washing Machine
MN085 Fabrication of Floating turbine
MN086 Fabrication of Solar grass Cutting Machine
MN087 Fabrication of Highway Wind turbine
MN088 Solar powered Auto charging grinding Machine
MN089 Solar Multi-Purpose (Agro/Seed) Sprayer
MN090 Solar Automated Track Guided Vehicle (Solar ATGV)
MN091 Pedal operated wet grinder with Cell phone charger
MN092 Exhaust Gas Power Generation by Blower
MN093 Fabrication of Solar peltier Air Conditioner
MN094 Fabrication of Pedal operated drilling Machine
MN095 Fabrication of Solar operated paddy Cutter
MN096 Fabrication of Solar Water fountain
MN097 Electrical energy can be produced by using vibration
MN098 Fabrication of Solar Electric GoPed Drive
MN099 Air Compressor using quick return Mechanism
MN100 Solar Automobile Air Conditioner
MN101 Electrical Power Generation using Thermal Power Plant
MN102 Fabrication of Solar room warmer
MN103 Hybrid Vehicle with regenerative Breaking in motor Cycle
MN104 Electrical Power Generation using steam Power Plant
MN105 Electrical energy produce by Vibration by using Foot step method
MN106 Electricity and Water Pumping System using Wind Mill
MN107 Fabrication of Wind Energy Vehicle
MN108 Fabrication of Battery Cycle
MN109 Power Generation from Pneumatic shock Absorber
MN110 Non-Conventional Door based Power Generation System
MN111 Solar Powered Automatic Fire Fighting Robot
MN112 Fabrication of Solar massager
MN113 Solar Water purification combined with FPC and ETC
MN114 Solar railway track crack detecting Vehicle
MN115 Solar operated weed Cutter for Agriculture
MN116 Fabrication of Solar fertilizer Sprayer
MN117 Fabrication of Solar Fan with Lighting System
MN118 Design and Fabrication of Bladeless Turbine with Propeller
MN119 Solar based advanced Vehicle movement System using windmill
MN120 Automatic drip Irrigation using Solar PV cell
MN121 Solar auto charged grinding and Cutting Machine
MN122 Fabrication of Solar Automobile Fridge
MN123 Automatic Solar foundation excavator Robot
MN124 Solar Air Dryer with multiple PCM
MN125 Fabrication of Double reflection Solar still
MN126 Nano Fluid based solar desalination using flashing technique
MN127 Design and Fabrication of Wind pump
MN128 Bio-Diesel extraction from waste plastic material
MN129 Solar Wheel Chair for physically Disabled
MN130 Fabrication of various types of Irrigation System
MN131 Power Generating Wind mill in highway by using fast moving Vehicle
MN132 Fabrication of Solar Train
MN133 Fabrication of Solar UPS
MN134 Fabrication of Air Compressor using Wind mill
MN135 Solar Powered Visitor Guided with Material Handling Vehicle
MN136 Fabrication of Power producing and Water pumping pendulum kit
MN137 Fabrication of Solar Power sprinkler
MN138 Fabrication of Waste oil burning System
MN139 Artificial Intelligent based Solar Vehicle
MN140 Energy conversion from Roadways using kinetic motion
MN141 Automatic Wind blade pitch controlling System
MN142 Fabrication of pedal operated Hacksaw with mobile charge
MN143 Solar still integrated with settling tank for effluent treatment
MN144 Automatic board cleaner using solar energy
MN145 Intelligent solar-powered Automobile ventilation System
MN146 Fabrication of man powered car
MN147 Fabrication of Diffuser Type Wind mill
MN148 Solar powered Tea Leaf cutting Machine
MN149 Electrical Power Generation using Speed Breaker
MN150 V-through special type Solar Water Heater
MN151 Fabrication of Solar Electric Gear bike
MN152 Fabrication of Solar wood cutter
MN153 Portable steam generator with iron box
MN154 Air Conditioning of an Automobile using Engine Exhaust gas
MN155 Solar aided portable vacuum desalination plant
MN156 Wind And Solar Hybrid Power Generation System for home
MN157 Electrical Power Generation System by using Gasifier
MN158 Cell phone controlled Solar Vehicle
MN159 Solar powered thermo-electric Refrigerator
MN160 New high tech walking electric bike using solar power
MN161 SMS controlled Solar Vehicle
MN162 Solar Agricultural Water Pumping System with Auto tracking
MN163 Fabrication of Power Generation from Francis turbine
MN164 Solar Automatic Stair climbing Wheel chair
MN165 Solar operated Automatic Seed Sowing Machine
MN166 Solar powered Vapour absorption Refrigerator
MN167 Fabrication of Solar Seed Dryer
MN168 Fabrication of pollution free Four Stroke Petrol Engine
MN169 Solar Automatic Traffic and Street Light Controller
MN170 Solar air Heater by using Solar still
MN171 Fabrication of Power Generation from Kaplan turbine
MN172 Piezoelectric Powered Cycle
MN173 Fabrication of Darrieus Rotor Wind turbine
MN174 Fabrication of Osmotic power plant
MN175 Fly Wheel based Water pumping System
MN176 Fabrication of Non-conventional Air Compressor
MN177 Fabrication of Energy produced from Running Vehicle
MN178 Fabrication of Solar Air Dryer
MN179 Advanced Solar Water Heater with Electricity Generation
MN180 Fabrication of Bicycle Wind turbine
MN181 Solar Water Purification by using thermal method
MN182 Fabrication of Automatic Solar Board Cleaner
MN183 Generation of electricity from cycling exercise
MN184 Solar Automatic head-lamp alignment System with dim/bright controller
MN185 Fabrication of Thermal storage unit using PCM
MN186 Solar Water service station for Two Wheeler
MN187 Design& Fabrication of Solar Powered Hotel Serving Robot
MN188 Low pressure Solar Water Heater with auto tracking
MN189 Fabrication of Pedal operated air Compressor
MN190 Fabrication of Solar Air Cooler
MN191 Effect of Nano Fluid in a modified vacuum single basin Solar still
MN192 MPPT control strategy for Wind energy conversion System
MN193 Fabrication of Water tunnel
MN194 Diffuser Type Hybrid Wind turbine
MN195 Solar Automated Guided Vehicle (Solar AGV)
MN196 Design and performance of a vacuum single basin Solar still
MN197 Design and Development of sand Power Generation
MN198 Pedal operated grinding Machine
MN199 Solar Kettle (or) Solar Parabolic Collector
MN200 Pedal cranking mechanism for paddy wheat threshing Machine
MN201 Multiple Power Generation from Solar energy, Wind mill and Rain water
MN202 Remote controlled solar oil skimmer Robot
MN203 Fabrication of Solar Seeds Sprayer
MN204 Design and Fabrication of manually track parabolic solar disc for in-house cooking
MN205 Foot operated plate cleaning Machine and dryer
MN206 Water Turbine Power Generation System
MN207 Fabrication of Automatic Solar Powered soil monitoring Robot
MN208 Reflecting mirror type solar steam generator
MN209 AI based Solar Vehicle and coin based electronic Bus conductor
MN210 Horizontal Turbine Type Domestic Wind Mill
MN211 Fabrication of Foot Step Power Generation
MN212 Fabrication of pedal operated vertical Hack saw Machine
MN213 Solar Air Cooler cum Heater with Auto Tracking
MN214 Fabrication of Solar Peltier air cooler cum Heater
MN215 Salt Water converted to purified drinking Water by using revolving gate
MN216 Fabrication of Water purifier Cycle
MN217 Photovoltaic thermal Hybrid Solar Water Heater
MN218 Non-Conventional Method of Water Pumping Using Vertical Wind Turbine
MN219 Design & Fabrication of Solar Street light with day night control
MN220 Coin Based Solar Mobile Phone Charger
MN221 Fabrication of Solar Car
MN222 Efficiency monitoring of a two Stroke Petrol Engine by using Air heat exchanger
MN223 Solar powered Automatic temperature controller with cooling System
MN224 Development of basin solar still by adding magnetic treatment unit and double glass cover provided with Water
MN225 Demonstration of Kinetic energy recovery System (KERS)
MN226 Fabrication of Green gym
MN227 Fabrication of Solar irrigation System
MN228 Fabrication and performance test of a model Solar Refrigeration System
MN229 Experimental analysis of Solar Water Heater using porous medium and Agitator
MN230 Solar grass Cutter with Water spraying System
MN231 Solar grass cutter with Automatic tracking
MN232 Solar Water Heater with parabolic collector
MN233 Fabrication of Incinerator cum generator
MN234 Multi Power Generation using Geneva Wheel Mechanism in Wind mill
ROBOTICS BASED PROJECTS:-
MR001 Fabrication of Air Powered Robot Car
MR002 Bluetooth operated three axis pick and place Robot
MR003 Theojanson Walking Robot Mechanism
MR004 Fabrication of Bore well child Rescuing Robot
MR005 Fabrication of Pipe Inspection Robot
MR006 Remote Controlled Video Analyzing pick and place Robot
MR007 Fabrication of Wall climber Robot
MR008 Intelligent oil skimmer Robot
MR009 Multi-purpose Agriculture Robot for Seed sowing with weed remover and fertilizer sprayer
MR010 Fabrication of Automatic Stair climbing Robot
MR011 Six leg kinematic walker Robot
MR012 Man less defense multipurpose Robot
MR013 Fabrication of Multi-utility Agriculture Vehicle
MR014 Fabrication of drainage cleaning Robot
MR015 Automatic fire fighting Robot with visitor guided
MR016 Solar operated portable vacuum cleaning Robot
MR017 Areca nut tree climbing and cutting Robot
MR018 Tread mill Bicycle with Power Generation
MR019 Fabrication of harvesting Seed putting & threshing Robot
MR020 Fabrication of Multi-purpose Soldier Robot
MR021 Solar grass Cutter with Water spraying Robot
MR022 Design and Fabrication of Automatic soil monitoring Robot
MR023 Automatic Scrap collecting Robot
MR024 Design& Fabrication of Hotel Serving Robot
MR025 Fabrication of Automatic chip and dust collecting Robot by using Blower
MR026 Automatic pick and place paint spraying Robot
MR027 Automatic foundation excavator Robot
MR028 Fabrication of Magnetic wall climbing Robot
MR029 Pneumatic Four (or) six Axis Material Handling Robot
MR030 Six leg Robot for Agriculture purpose which can spray Seed and water
MR031 Remote controlled bomb detecting Robot
MR032 PIR based human focus movement Robot
MR033 IVRS Based Control of Alive Human Being Detector with Voice Feedback
MR034 Automatic Vehicle Accident Information System
MR035 Automatic Air delivery System based on density of oxygen in Car cabin
MR036 Rescue Robot for Military Purpose
MR037 SMS Enabled Autonomous Robotics for Military
MR038 Fabrication of Exo-support for legs
MR039 Building an Autonomous Light Finder Robot
MR040 Cell Phone controlled pick and place Robot
MR041 Fabrication of Automatic sweeping Vehicle
MR042 Walking Robot with Hyper Line Tracker Using IR Sensors
MR043 Automatic Human Seeker Robot with Body Heat Scanner
MR044 Real time security guard Robot using GSM / CDMA networking
MR045 Fabrication of man powered Car
MR046 Distance Monitoring and Object Detecting Robot
MR047 Fabrication of Water purifier Cycle
MR048 Fabrication of Agricultural Robot
MR049 Remote controlled paint spraying Robot
MR050 Rescue Robot for Deep Well
MR051 Object detection and Vibration alert to blind people
MR052 Wireless PC based Voice Based Path Control Robot
MR053 Fabrication of 360 degree parking assistance System
MR054 Fabrication of Quad bike
MR055 Autonomous Navigation of Intelligent Robots for Risky Interventions
MR056 Fabrication of Portable Sweeping Vehicle
MR057 Fabrication of under Water Robot
MR058 Fire Fighting Robot with Auto Dialer Facility
MR059 Accelerometer and tactile controlled Robot
MR060 Hydraulic based emergency Rescue ladder Robot for Fire Accident
MR061 Robot Assistive limb for physically challenged people
MR062 An intelligent mobile Robot navigation technique using RFID Technology
MR063 Fabrication of Fire Fighting Robot
MR064 Automatic Scrap collecting & Disposing Vehicle
MR065 Fully Automated Track Guided Vehicle (ATGV)
MR066 SMS controlled video analyzing Robot
MR067 Smart Tanker Robot for Security Operations
MR068 90 degree Four Wheel turning Steering Mechanism
MR069 Button operated Motorized portable mini crane
MR070 Wheel chair using Eye shadow and touch screen
MR071 CPR parallel Robot for hart patient in hospital application
MR072 Solar operated Automatic Seed Sowing Vehicle
MR073 Automatic convertible Wheel Chair cum bed
MR074 Automatic lawn mower Robot
MR075 Robot with Search and Rescue Feature for an Accident Area or Natural Disaster Area
MR076 Automatic medicine dispenser for sugar patient
MR077 Kinematics analysis of a parallel Robot with a passive segment
MR078 Automated prosthetic leg for physically challenged People
MR079 Pneumatic visual landing Gear with Automatic Tyre pressure inflation System for aircraft
MR080 Solar powered Water weed Cutter Robot
MR081 AI based Solar Vehicle and coin based electronic Bus conductor
MR082 Blue tooth operated Wheel chair
MR083 Fabrication of Mini Robot Car
MR084 SMS based automated guided Vehicle
MR085 Automated Guided Vehicle (AGV)
MR086 Electro-Magnetic scrap collecting Vehicle
MR087 Automatic open well cleaning Robot
MR088 SMS Based Alive Human Detector in Affected Areas/War Fields
MR089 Pneumatic Double axis JCB Robot
MR090 Self-propelled Cutter suction dredger with bow thruster for ship
MR091 Theojanson Mechanism for Walking Chair
MR092 Remote Controlled Water Splash Robot for Gardening
MR093 Automatic portable groundnut planting Robot
MR094 Fabrication of Swirl gripper
MR095 Fabrication of air ship
MR096 Fabrication of Human Eye Robot
MR097 Object Tracking Robot Using Image Processing
MR098 Fabrication of Wheel chair cum stretcher model
MR099 Belt model based stair climbing Wheel chair
MR100 Fabrication of Path finding Robot
MR101 Fabrication of mechanical spider Robot
MR102 Automatic Vehicle overload alert System
MR103 Automatic motorized Arc Welding Robot
MR104 Simple leg walking mechanism
MR105 Automatic scrap Compression Vehicle
MR106 Human detection in Robot Search & Rescue using PIR
MR107 Automatic Car washing System by using IR Sensor
MR108 Fabrication of Unaided Guided Vehicle (UGV)
MR109 Fabrication of Bipedal walking Robot
MR110 Design & Development of standing Wheel Chair
MR111 Image processing based PC inspection Robot
MR112 Fabrication of Anti drown Vehicle
MR113 Watchdog – Robot Inspector for a Fire Hazards Area
MR114 New high tech walking electric bike using solar power
MR115 Fabrication of Firefighting AGV
MR116 Magnetic levitation flight landing System
MR117 Artificial Intelligent based Solar Vehicle
MR118 Fabrication of Automatic Paint spraying Robot
MR119 Neural control of a fully actuated biped Robot
MR120 Fabrication of Unpowered exoskeleton boot
MR121 Multiple roller handling Pneumatic manipulator
MR122 Fabrication of Vacuum assisted wall climber
MR123 Fabrication of Easy Lift Stairs
MR124 Pneumatic Four axis brick handling Robot
MR125 Fabrication of Pneumatic Ball Printing Robot
MR126 Fully covered Two Wheeler with Automatic extra Wheel balancing System
MR127 Fabrication of Go-kart car
MR128 Fabrication of Stroke therapy Chair
MR129 Robot controlled Vacuum Cleaner
MR130 SMS Based Automatic Vehicle Accident information System
MR131 Fabrication of unaided Automatic tri Cycle
MR132 Visitor guided with material handling Robot
MR133 Automatic grass cutting by using Sensor
MR134 AI Based Automatic Path finding Cum Video Analyzing Robot
MR135 Automatic Steering Control Robot
MR136 An optical method of Foot pressure monitoring & therapy for paralyzed patient
MR137 Remote operated weapons Robot for Military
MR138 Fabrication of Concrete spray Robot
MR139 Wheel Chair for Paralyzed People
MR140 Accelerometer controlled Robot using mobile phone
MR141 Ripened fruit identification and picking Robot
MR142 Multi tasked smart Wheel chair for physically challenged people
MR143 Autonomous Line tracking Robot with Obstacle Avoidance
MR144 Solar operated weed Cutter for Agriculture
MR145 Voice operated intelligent mobile Robot
MR146 Fabrication of Tennis ball collector Robot
MR147 Fabrication of Fly car
MR148 Fabrication of Solar operated paddy Cutter
MR149 Pick and Place Robot with Remote Control
MR150 Fabrication of Robot manipulator
MR151 Automatic Smart Robot for Library
MR152 Hydro-Pneumatic moving Vehicle
AGRICULTURE AND DOMESTIC BASED PROJECTS:-
AG001 Fabrication of potato Peeling & Slicing Machine
AG002 Engine Operated Multi utility agricultural Vehicle
AG003 Multi-purpose Agri Cutter
AG004 Automatic Ginger cutting, feeding and drying Machine
AG005 Motorized Coconut Dehusking Machine
AG006 Hydraulic 3 axis Modern Trailer for Agriculture
AG007 Hybrid Solar & Wind Power Generation System for agriculture
AG008 Fabrication of Banana fiber Extracting Machine
AG009 Advanced wireless Automatic digital pumping System for Agriculture using Sensor
AG010 Fabrication of coconut Tree sprayer
AG011 Multi-purpose Agriculture Vehicle for Seed sowing with weed remover and fertilizer sprayer
AG012 Agricultural Motor Pump Running using Solar Power with Auto Tracking
AG013 Fabrication of harvesting Seed Putting & Threshing Vehicle
AG014 Solar grass Cutter with Automatic sun tracking System
AG015 Pneumatic 3 Axis Modern Trailer for agriculture
AG016 Power production and Water pumping from Speed Breaker
AG017 Solar grass Cutter with Water spraying System
AG018 Electricity and Water Pumping System using Wind Mill
AG019 Multiple Power Generation from Solar energy, Wind mill and Rain water
AG020 Coconut tree climbing and cutting Machine
AG021 Six leg Robot for Agriculture purpose which can spray Seed and water
AG022 Semi Automated Areca Nut Collecting conveyor
AG023 Pedal operated Washing Machine for Cloth
AG024 Fabrication of Paddy harvesting and threshing Machine
AG025 Design & Development of semi-Automatic feeding Mechanism for small scale Poultry farm
AG026 Fabrication Solar Agro Sprayer
AG027 Fabrication of Pepper Thresher Machine
AG028 Onion peeling and Automatic Pneumatic Cutting Machine
AG029 Solar operated Automatic Seed Sowing Machine
AG030 Automatic Idli batter filling Mechanism
AG031 Fabrication of low cost harvesting Machine
AG032 Generation of Electrical Power using municipal social waste
AG033 Fabrication of Solar Water fountain
AG034 Generation of electricity from cycling exercise
AG035 Tree branch cutting Machine
AG036 Power Generation from sea Water by MHD Power Generation method
AG037 Pedal cranking mechanism for paddy wheat threshing Machine
AG038 Fly Wheel based Water pumping System
AG039 Fabrication of various types of Irrigation System
AG040 Automatic Fault Egg Sorting Machine
AG041 Semi-autonomous Multi-purpose Cleaning Vehicle
AG042 Experimental setup on Gasifier
AG043 Fabrication of Under Water Vehicle
AG044 GPS Guided Modular design Mobile Robot platform for agricultural Applications
AG045 Fabrication of coconut grater and milk extractor
AG046 Fabrication of Portable sweeping Machine
AG047 Fabrication of Sun flower harvesting Machine
AG048 Pedal cloth washing Machine with Drier
AG049 Fabrication of Automated gardener
AG050 Fabrication of Automatic conveyor based Rice batching Machine
AG051 Automatic seeds weighing and Packing Machine
AG052 Hydraulic based emergency rescue ladder for fire Accident
AG053 Solar Cabinet Seed Drier integrated with biomass
AG054 Double side Hacksaw cutting Machine using scotch yoke Mechanism
AG055 Fabrication of Maize De-Husker
AG056 Automatic drainage cleaning and detection of toxic gases
AG057 Design and Fabrication of hand operated fertilizer blender
AG058 Fabrication of Water purifier Cycle
AG059 Fabrication of Solar vegetable Air dryer
AG060 Design and development of sand Power Generation
AG061 Pendulum based Water pumping System
AG062 Fabrication of Motorized Agri Cutter
AG063 Fabrication of Automatic sweeping Vehicle
AG064 Fabrication of Agricultural model pump
AG065 Fabrication of Agricultural Robot
AG066 Fitness equipment for localized electrical Power Generation
AG067 Fabrication of Low cost sugarcane harvester
AG068 Foot operated plate cleaning Machine and dryer
AG069 Fabrication of Motorized Lawn Mover
AG070 Fabrication for converting waste plastic to Diesel Fuel
AG071 Fabrication of Motorized plant Cutter
AG072 Water overflow controlling System
AG073 Design & Fabrication of Engine operated tiller cultivator
AG074 Automatic weighing and Sealing Machine
AG075 Solar enhanced energy efficient food processor
AG076 Pedal operated biomass briquetting Machine
AG077 Automatic Pneumatic Coconut Cutting Machine
AG078 Pedal operated Solar Cell phone Charger
AG079 Automatic portable groundnut planting Machine
AG080 Fabrication of Multipurpose seed Shower
AG081 Motor operated vegetable cutting Machine
AG082 Fabrication of wood grooving Machine
AG083 Fabrication of Role Type Agro Sprayer
AG084 Bio Fuel extractor from Bio Oil
AG085 Fabrication of sugarcane juicer Machine
AG086 Fabrication of vegetable Slicing Machine
AG087 PLC based Automatic Rotary Water Bottle filling System
AG088 Pneumatic Coconut Husk remover & Shell Cutter
AG089 Solar powered Tea leaf cutting Machine
AG090 Water overflow controlling System
AG091 Fabrication of Beans Sheller Machine
AG092 Automatic medicine dispenser for sugar patient
AG093 Fabrication of groundnut thruster
AG094 Automatic grass Cutter by using Sensor
AG095 Automatic rubber tapping Machine for moving one tree to another tree
AG096 Fabrication of crank shaft operated agriculture cutter
AG097 Fabrication of Solar Seed Dryer
AG098 Fabrication of Solar wood Cutting Machine
AG099 Water Pumping System using Wind Power
AG100 Fabrication of drainage cleaning Machine
AG101 Fabrication of Lawn Mower
AG102 Solar powered Water weed Cutter
AG103 Fabrication of Solar Seeds Sprayer
AG104 Fabrication of Multi Agri cutter
AG105 Pedal Operated Agricultural Water pumping System
AG106 Scotch yoke Mechanism based Water pumping System
AG107 Semi-Automatic Water tank cleaner
AG108 Fabrication of Tomato grader
AG109 Hydro Power plant with salt Water purification System
AG110 Power Generation from organic waste of college canteen
AG111 Automatic Moisture and Light Controlling System for Garden
AG112 Fabrication of Air Compressor using Wind mill
AG113 Portable vegetable cutter and slicer
AG114 Fabrication of Centrifugal Pump apparatus
AG115 Fabrication of Pipe line turbine Power Generation
AG116 Pneumatic scissor jack for loading vegetables to lorry
AG117 Fabrication of Modified sand Muller
AG118 Fabrication of Solar Agro Sprayer
AG119 Fabrication of green gym
AG120 Fully Automated potato Chip Slice making Machine
AG121 Fabrication of Motorized plant trimmer
AG122 Fabrication of Smart Cradle with timer
AG123 Fabrication of Rubber tree tapping Machine
AG124 Fabrication of biomass briquetting Machine
AG125 Automatic scrap collecting & Disposing Machine
AG126 Fabrication of Universal cutter
AG127 Solar Powered Agricultural Water Pumping System
AG128 Fabrication of briquette burner
AG129 Automatic drip Irrigation for precision Agriculture
AG130 Automatic Water level Sensing Crane for Agricultural Pump
AG131 Fabrication of paddy cleaner for agro seeds
AG132 Fabrication of Power Generation from Francis turbine
AG133 Fabrication of Pneumatic ground driller
AG134 Fabrication of coconut scraping Machine
AG135 Fabrication of Power Generation from Kaplan turbine
AG136 Fabrication of Groundnut Harvester
AG137 Pneumatic press for coconut pith blocking Machine
AG138 Design& Fabrication of Hotel Serving Robot
AG139 Fabrication of motor less weed cutter
AG140 Hybrid flour mixing Machine
AG141 Design and Fabrication of Automatic soil monitoring Robot
AG142 Design and development of natural vegetables / fruits Preservator
AG143 Gas Converted Power Sprayer
AG144 Fabrication of Solar Power sprinkler
AG145 Solar seed dryer with multiple PCM
AG146 Areca nut tree climbing and cutting Robot
AG147 Design and Fabrication of Wind pump
AG148 Fabrication of Solar Birds Scarer
AG149 Automatic Drip Irrigation using Solar PV cell
AG150 Fabrication of Mechanical seed thruster
AG151 Bio-Diesel extraction from waste plastic material
AG152 Fabrication of Seed crushing Machine
AG153 Agricultural Paddy Cleaning System by using Solar Power
AG154 Fabrication of Solar Seeds Sprayer
AG155 Solar operated weed Cutter for Agriculture
AG156 Fabrication of decorticator seed kernel extractor
AG157 Fabrication of Seeds Sprayer
AG158 Push operated Agriculture spray Pump for Garden
AG159 Fabrication of Groundnut shelling Machine
AG160 Rear Wheel Steering for Trailer trucks
AG161 Fabrication of Solar operated paddy Cutter
AG162 Fabrication of Laminar flow Water fountain
AG163 Fabrication of Motorized oil mill Mechanism
AG164 Semi-Automatic Weed remover in sugarcane farm
AG165 Viability of used sunflower oil as a substitute for Diesel
AG166 Two stage Mechanical Water pendulum oscillator
AG167 Fabrication of Rotary Kaller
AG168 Automatic Vegetable (or) Lemon Cutting Machine
AG169 Fabrication of Solar grass Cutting Machine
AG170 Solar seed Dryer with Auto Tracking
AG171 Automatic plastic separation module for municipal solid waste
AERONAUTICAL AND MARINE BASED PROJECTS:-
AE001 Digital Automatic Tyre pressure inflation and monitoring System for Aircraft
AE002 Fabrication of Magnetic Levitation Flight landing System
AE003 Pneumatic vertical Lift Mechanism of a Bridge at the time of ship arrival
AE004 Fabrication of Remote controlled Hovercraft
AE005 Air Conditioning of an Automobile using Marine Engine Exhaust gas
AE006  Emergency Hydraulic Steering used in ship
AE007 Pneumatic visual landing Gear with Automatic Tyre pressure inflation System for aircraft
AE008 Remote controlled oil skimmer Robot for marine application
AE009 Self-propelled Cutter suction dredger with bow thruster for ship
AE010 Fabrication of Sub Marine (Model)
AE011 Solar powered Peltier Aero plane cabin cooling System
AE012 Fabrication of Remote controlled Air Craft
AE013 Solar powered agriculture Aircraft for seed and Fertilizer Sprayer
AE014 Turbojet Engine with Active Magnetic Bearing
AE015 Intelligent obstacle warning System for ship
AE016 Fabrication of Under Sea Water Robot
AE017 Fabrication of combustion chamber for rocket Engine
AE018 Fabrication of Water Fuel Engine for Mini Boat
AE019 Pipe line Drainage cleaning Robot
AE020 Fabrication of mine detecting hover craft with camera
AE021 Exhaust Gas Power Generation by using Blower
AE022 Automatic Accident Avoiding System for Ship by using Obstacle sensor
AE023 Cyclone separator with blower
AE024 Fabrication of Floating Wind Turbine
AE025 Aero plane Run way monitoring and checking System by using webcam
AE026 Lubrication oil cooing System for Ship
AE027 Solar powered Water weed Cutter floating Ship
AE028 Aero plane Controlling System (Glider model)
AE029 Silencer Fabrication of centrifugal blower
AE030 Increasing the Efficiency of Turbo Charger during low Engine Speed by turbo-lag reduction
AE031 Fabrication of SMS controller Air Craft
AE032 (VIVACE) a new concept in Generation of clean and renewable energy from fluid flow
AE033 Automatic fire safety System for Fuel tank and Engine for Aero plane
AE034 Alternate Fuel for Marine Engine
AE035 Fabrication of manual operating spoiler in a Vehicle
AE036 Fabrication of Cryogenic Engine using liquid nitrogen
AE037 Fabrication of Aluminium sail boat
AE038 Fabrication of Fly car
AE039 Fabrication of Under Water Vehicle
AE040 Sea Water converted to drinking Water by using Solar Power
AE041 Fabrication of Pneumatic Steering for ship
AE042 Fabrication of Opposite Piston opposite Cylinder (OPOC) Engine
AE043 Fabrication of Osmotic power plant
AE044 Fabrication of air ship
AE045 Fabrication of liquid propellant rocket Engine with Gimballing and GSM for control ignition and thrust vectoring
AE046 Fabrication of pulse jet Engine
AE047 Automatic digital Tyre pressure inflation and deflation System for aircraft
AE048 Solar powered remote controlled aircraft
AE049 Fabrication of Hydrophone System in ship
AE050 Demonstration of magneto frictional propulsion System
AE051 Electro Hydraulic Steering System for Ship
AE052 Fabrication of Mini Jet Engine
AE053 Aero plane Visual landing Gear arrangement with Tyre Pressure Inflation System
AE054 Vertical Lift Mechanism for Kattwyk Bridge at the time of ship arrival
AE055 Acetylene powered Jet Engine
AE056 Fabrication of Marine Engine Model
AE057 Fabrication of Totally Enclosed Life Boat
AE058 Fabrication of Anti hijack Systems for Aero plane
AE059 Aero plane Controlling System (Flying Model)
AE060 Fabrication of suction dredger for ship
AE061 Fabrication of porter governor
AE062 GPS based ship navigation System
AE063 Fabrication of Aerodynamic design for Buses
AE064 Fabrication of a single Engine hovercraft
AE065 Automatic two ram Hydraulic Steering of ship
AE066 Fabrication of black box in aero plane
AE067 Refrigeration using waste heats From Marine Engine
AE068 Air propulsion motor boats with remote control
TOOL & DIE (AND) JIG & FIXTURE BASED PROJECTS:-
TD001 Pneumatic Cutting and grinding and shaping Machine
TD002 Fabrication Motorized Double side Hack Cutting Machine
TD003 Concave jig attachment for lathe
TD004 Automatic Sheet metal Feeding & Cutting Machine
TD005 Punching Machine using whit worth mechanism
TD006 External and internal grinding Machine attachment for lathe
TD007 Automatic Gear milling Machine by using proximity sensor
TD008 Dual shaping Machine with width worth Mechanism
TD009 Fabrication of Electro Magnetic Moulding Machine
TD010 Hammering operation by using Vinci-cam Mechanism
TD011 Automatic boring mechanism for foundry
TD012 Pneumatic Hacksaw Machine with shaping attachment
TD013 Gear cutting jig attachment for lathe
TD014 Fabrication of Motorized Embossing drilling Machine
TD015 Universal tool grinding Machine
TD016 Surface finish measuring equipment with digital display
TD017 Pneumatic injection Moulding die Machine
TD018 Fabrication of indexing drill jig using bevel Gear
TD019 Pneumatic Paper cup making Machine
TD020 Pneumatic multi nut’s spanner box with torque wrench
TD021 Auto Indexing Gear cutting attachment for Pneumatic shaping Machine
TD022 Fabrication of Automatic Tool Retrieval System
TD023 Fabrication of Indexing jig for milling fixture
TD024 Automation of Vibro cleaning process in a typical die casting industry
TD025 Fabrication of Automatic Colour code sensing punching Machine
TD026 Fabrication of pin on disc wear testing Machine
TD027 Fabrication of Pneumatic punch die
TD028 Tool and Die Design for Piercing Tool
TD029 Fabrication of Multi Axis Modular Fixture
TD030 Fabrication of leaf jig
TD031 Fabrication of Automatic blanking Machine
TD032 Tool and die design for Blanking
TD033 Fabrication of Multi-purpose Cutting Machine
TD034 Fabrication of riser removal in the casting by Pneumatic piston
TD035 Tool and die design for compound tools
TD036 Fabrication of Pneumatic plastic crushing Machine
TD037 Design & Fabrication of tool cutting force dynamo meter on lathe
TD038 Fabrication of Modified sand Muller
TD039 Fabrication of Pneumatic drill jig
TD040 Fabrication of Vertical milling fixture
TD041 Pneumatic Mould making Machine for Gear wheel
TD042 Fabrication of Hydraulic Bearing Puller
TD043 Design & Fabrication of spring punching Machine
TD044 Fabrication of Porter Governor
TD045 Indexing jig for drilling Machine
TD046 Fabrication of Progressive Die
TD047 Fabrication of Tilting Vice
TD048 Fabrication of Mould making for table Bush
TD049 Fabrication of Wood Grooving Machine
TD050 Tool and die design for Gravity Mould
TD051 Hydraulic Pneumatic disc Break
TD052 Slotting attachment in drilling Machine
TD053 Fabrication of internal thread Cutting Machine
TD054 Universal tapping Machine
TD055 Fabrication of Shaft run out checker Machine
TD056 Fabrication of Pneumatic pellet press
TD057 Tool and die design for Automatic filling – vertical flow tools
TD058 Cutting Machine by Four bar Mechanism
TD059 Pneumatic slotting tool Machine
TD060 Twin spindle drill holder
TD061 Mechanical CAN crusher by using quick return Mechanism
TD062 Tool and die design for Automatic filling – horizontal flow tools
TD063 Tool and die design for bending tools
TD064 Double side Hacksaw Machine using scotch yoke Mechanism
TD065 Hand operated plate bending Machine
TD066 Fabrication of external vertical thread Cutting Machine
TD067 Automatic Pneumatic brick making die Machine
TD068 Manual operated Multi nut tightner
TD069 Tool and die design for Progressive tools
TD070 Pneumatic Vice for holding round objects
TD071 Design & Fabrication of sandwich jig
TD072 Multi-purpose Pneumatic Sheet Cutting and Sheet bending Machine
TD073 Pneumatic can crushing die Machine
TD074 Design and analysis of press tool Machine
TD075 Design and Fabrication of universal jaw
TD076 Fabrication of Reversible blanking dies
TD077 Tool and die design for Deep drawing
TD078 Automatic multi axis drilling Machine
TD079 Tool and die design for Automatic filling -Hand Mould tool
TD080 Tool and die design for forming
TD081 Fabrication of Hydraulic brick making Machine
TD082 Automatic fixer using sensor
TD083 Metal Polishing Using Abrasive Jet Machine
TD084 Pneumatic leaf cup die Machine
TD085 Fabrication of universal Fixture
TD086 Manual operated pipe bending Machine
TD087 Design and Fabrication of Pneumatic forging Machine
TD088 Fabrication of Pneumatic bell crank press
TD089 Motorized Multi-purpose cutting Machine by using cam Mechanism
TD090 Design and Fabrication of combination dies
TD091 Tool and die design for combination tools
TD092 Design and Fabrication of Pneumatic Punching and Slotting Machine
TD093 Design and Fabrication of Bar bending Machine
TD094 Tool and die design for Machine Mould
TD095 Tool and die design for trimming tools
TD096 Eccentric punching die Machine
TD097 Multi use tool post grinder attachment for lathe
TD098 Pneumatic bearing puller
TD099 Hydraulic press for foundry ramming Machine
TD100 Milling jig attachment for lathe
TD101 Fabrication of chain hooks separator & pressing Machine
TD102 Design and Fabrication of piercing dies
TD103 Vacuum Bag Moulding Die Machine
TD104 Fabrication of plastic crushing and Moulding Machine
PNEUMATIC AND HYDRAULIC BASED PROJECTS:-
PH001 Fabrication of Hydro-Pneumatic moving Vehicle
PH002 Active brake torque vectoring in Differential unit
PH003 Onion peeling and Automatic Pneumatic slicing Machine
PH004 Intelligent Active Suspension System for Two Wheeler
PH005 Fabrication of Geneva conveyer with Pneumatic pin punch
PH006 Fabrication of Air brake System by using Engine Exhaust gas
PH007 Fabrication of Riser removal in the casting Pieces by Pneumatic piston
PH008 Multi-purpose Pneumatic Sheet Cutting and Sheet bending Machine
PH009 Power Generation of Speed Breaker by using Hydraulic System
PH010 Compressed air production using Vehicle suspensor
PH011 Automatic digital Tyre Pressure Inflation and Deflation System
PH012 Pneumatic controlled steps in Bus with Break locking System
PH013 Automatic Hand Brake System by using Pneumatic interface
PH014 Safety System to avoid Accident when Driver in sleep
PH015 Pneumatic disc Brake System by using Engine Exhaust gas
PH016 Automatic Differential unit locking System for Four Wheeler
PH017 Pneumatic Hacksaw Machine with shaping attachment
PH018 Eye blink sensor based Automatic Breaking and Bumper System
PH019 Button operated Pneumatic Gear shifting System for Two Wheeler
PH020 Fabrication of Three axis Pneumatic Modern Trailer
PH021 SMS based Pneumatic punching and Riveting Machine with Avoid Accident
PH022 Pneumatic six axis material handling Equipment
PH023 Inbuilt Hydraulic jack coupled with Engine for Four Wheeler
PH024 Automatic Colour code sensing and Punching Machine
PH025 Integrated automated Pneumatic jacks for Four Wheelers
PH026 Automatic Pneumatic Bumper and Break actuation before collision
PH027 Automatic Pneumatic T-Shirt folding Machine
PH028 Automatic Pneumatic Gear milling Machine
PH029 Digital Automatic Tyre pressure inflation and monitoring System
PH030 Magneto rheological fluid (MRF) Braking System
PH031 Pneumatic CAN crusher with Automatic feed Mechanism
PH032 Automatic Pneumatic Sheet metal feeding & Cutting Machine
PH033 Electro Hydraulic System for Automation in Vehicle
PH034 Automatic wall painting sprayer Machine
PH035 Fabrication of Pneumatic powered Bicycle
PH036 Fabrication of Advanced Emergency Braking System
PH037 Pneumatic Operated Emergency Braking System (EBS)
PH038 Hydraulic press for foundry ramming Machine
PH039 Automatic two ram Hydraulic Steering of ship
PH040 Automatic Lifting Vehicle inbuilt attached Hydraulic jack
PH041 Hydraulic sheet bend / bend Removing Machine
PH042 Fabrication of Automatic Air bag System for Two Wheeler
PH043 Pneumatic multi nut’s spanner box with Torque Wrench
PH044 Kinematics analysis of a parallel Robot with a passive segment
PH045 Pneumatic Bending / Bend Removing Machine
PH046 Automatic paper rolling and Pneumatic sealing Machine
PH047 Pneumatic Mould making Machine for Gear wheel
PH048 Design and Fabrication of human Air bag
PH049 Fabrication of Automatic Pneumatic plastic crushing Machine
PH050 Pneumatic Auto feed Drilling Machine
PH051 Fabrication of Hydraulic spoon turbine
PH052 Pneumatic Operated Inspection conveyor
PH053 Automatic Pneumatic vice and jack
PH054 Hydraulic based emergency rescue ladder for Fire Accident
PH055 Fabrication of Hydraulic Lift with Power pack
PH056 Working of Air Conditional unit using damping effect of shock absorber
PH057 Fabrication of Hydraulic fork lift
PH058 Fabrication of Hydraulic shearing Machine
PH059 Accident avoiding System for Punching Machine
PH060 Hydraulic Lifting System for Four Wheelers
PH061 Automatic emergency exit and tyre pressure inflation System
PH062 Design and Fabrication of bar bending Machine
PH063 Fabrication of Hydraulic clamping device with Power pack
PH064 Automatic PVC Pipe Feeding and Cutting Machine
PH065 Hydro-Pneumatic Vice with Pressure Booster
PH066 Fabrication of Hydraulic bearing puller
PH067 Fabrication of Pneumatic Belt Conveyor
PH068 Pneumatic Auto Feed Riveting Machine
PH069 Fabrication of Pneumatic Steering System for Car
PH070 Automatic Fault Egg sorting Machine
PH071 Hydraulic Break show Riveting Machine
PH072 Pneumatic Coconut Husk Remover & Shell Cutter
PH073 Auto Indexing Gear cutting attachment for Pneumatic shaping Machine
PH074 Motorized triangular air Compressor
PH075 Power production and Water pumping from Speed Breaker
PH076 SMS Pneumatic punching and riveting with avoiding Accident System
PH077 Pneumatic double side cutter width work Mechanism
PH078 Fabrication of Pneumatic conveyor
PH079 Three axis Hydraulic Modern Trailer
PH080 Fabrication of Bore well child rescuing Machine
PH081 Fabrication of Pneumatic Power Generation
PH082 Fabrication of Magneto Rheological clutch with Load Test
PH083 Conveyor Based Automatic Dimension Rejection System
PH084 Fabrication of Pneumatic trainer kit
PH085 Automatic parking Breaking System for Automobile
PH086 Design & Fabrication of conveyor automation with dimension inspection
PH087 Pneumatic Coconut Dehusking Machine
PH088 Fabrication of Hydraulic boring Machine
PH089 Pneumatic Vice for holding round objects
PH090 Compressor Gas level digital indicator with alarm System
PH091 Pneumatic Gear tooth grinding Machine
PH092 Anti-Theft Wheel locking System with SMS alert
PH093 Automatic hydro-Pneumatic Lubrication System
PH094 Pneumatic Multipurpose Grinding Machine
PH095 Automatic Hydraulic weight Lifting jack with crank arrangement
PH096 Fabrication of Anti drown Vehicle
PH097 Fabrication of Foot operated Hydraulic vice
PH098 Air Compressor using quick return Mechanism
PH099 Hydraulic armature bearing Remove System
PH100 Fabrication of Air Compressor using Wind mill
PH101 Automatic Pneumatic Spring End Grinding Machine
PH102 Automatic Sensor Operated Pneumatic Braking System
PH103 Auto discharge Mechanism for Pneumatic punching Machine
PH104 Pneumatic acrylic sheet bending Machine
PH105 Injection molding for key cover plate
PH106 Portable Pneumatic Spot welding Machine
PH107 Fabrication of Paper Cup Making Machine
PH108 Pneumatic time reduction in Shaping Machine
PH109 Fabrication of safety added Pneumatic Cutting Machine
PH110 Pneumatic road marking Machine
PH111 CPR parallel Robot for hart patient in hospital application
PH112 Super charging an Engine using Vehicle suspension
PH113 Pneumatic Operated Intelligent Braking System (IBS)
PH114 Button operated Pneumatic Gear changer in Two Wheeler
PH115 Fabrication of Pneumatic cargo weight lifter
PH116 Digital Hydraulic spring testing Machine
PH117 Automatic Pneumatic Ramming Machine
PH118 Regenerative Braking System using Pneumatic interface
PH119 Fly Wheel based Water pumping System
PH120 Hydraulic lifting System for Four Wheeler
PH121 Pneumatic Leaf-Cup Making Machine
PH122 Power Generation from Pneumatic shock Absorber
PH123 Fabrication of Hydraulic Lift with Pressure Booster
PH124 Pneumatic Four (or) Six axis JCB Equipment
PH125 Automatic Pneumatic Board cleaner
PH126 Automatic Pneumatic Jack for Four Wheeler
PH127 Automatic Pick and Place paint spraying Equipment
PH128 Design and Fabrication of Pneumatic Punching and Slotting Machine
PH129 Magneto hydro dynamic (MHD) Breaking System
PH130 Pneumatic Envelope Cover making Machine
PH131 Automatic Pneumatic Gear changer for Two Wheeler
PH132 Fabrication of Hydraulic Tail Stock
PH133 Pneumatic Reciprocating Water Pumping System
PH134 Automatic Pneumatic Reciprocating Grinding Machine
PH135 Fabrication of Pneumatic Railway Track changer
PH136 Fabrication of Mini Hydraulic Zip Crane
PH137 Fabrication of Smart energy monitoring Break over module
PH138 Pneumatic Cutting and Grinding and Shaping Machine
PH139 Pneumatic Operated Anti-Lock Braking System (ABS)
PH140 Pneumatic Double Axis Escalator Arm
PH141 PLC based Automatic Pneumatic drilling Machine
PH142 Automatic Pneumatic Bottle Washing Machine
PH143 Fabrication of Pneumatic scissor Lifter
PH144 Pneumatic vertical Lift Mechanism of a Bridge
PH145 Hydraulic TMT Rod bending Machine
PH146 Fabrication of Air powered Cycle
PH147 Automatic paint spraying Equipment
PH148 Pneumatic Reciprocating Hack saw Machine
PH149 Pneumatic visual landing Gear with Automatic Tyre pressure inflation System for aircraft
PH150 Fabrication of Hydraulic Sensing cutting Machine
PH151 Pneumatic Anti-theft Steering System
PH152 Modified Accident prevention Crash Guard by using Sensor
PH153 Fabrication of Mini Hydraulic Press
PH154 Fabrication of Hydro Pneumatic disc Break
PH155 Fabrication of Button operated Hydraulic jack
PH156 Automation in diode assembly for industry automation
PH157 Multiple roller handling Pneumatic manipulator
PH158 Fabrication of Automatic nut inspection conveyor
PH159 Fabrication of Pneumatic Steering for ship
PH160 Automatic Electro Hydraulic Jack
PH161 Automatic Electro Hydraulic Braking System
PH162 Fabrication of Air powered Wheel chair
PH163 Fabrication of Pedal operated Air Compressor
PH164 Pneumatic Four axis brick handling Robot
PH165 Fabrication of Hydraulic brick making Machine
PH166 Automated paper cup Feeding and making Machine
PH167 Remote controlled Car / Bus door open / close mechanism
PH168 Fabrication of Pneumatic garage door opener
PH169 Hydraulic sheet bending Machine with power pack
PH170 Automobile suspension made of Hydraulic magneto rheological damper
PH171 Fabrication of Auto feed Pneumatic vice
PH172 Fully Automated Hydraulic crane
PH173 Quick Lifting Hydraulic jack with Gear arrangement
PH174 Metal polishing using Abrasive jet Machine
PH175 Pneumatic biomass briquetting Machine
PH176 Fabrication of Pneumatic Automatic Printing Press
PH177 Fabrication of coconut tree Agro sprayer
PH178 Double axis Pneumatic JCB Equipment
PH179 Fabrication of potato peeling & slicing Machine
PH180 Electronic Assisted Hydraulic Breaking System
PH181 Pneumatic Cutting and Grinding Machine
PH182 Pneumatic plastic crushing and injection Moulding Machine
PH183 Pneumatic Multipurpose Press
PH184 Pneumatic Speed Breaker with day and night control
PH185 Pneumatic Bumper and Breaking with head light dim & bright controller
PH186 Combination of emergency, intelligence and anti-lock Braking System
PH187 Hydraulic parking attachment for Car
PH188 Fabrication of Hydraulic sheet cutting Machine
PH189 Fabrication of Pneumatic Auto Gear changer
PH190 Pneumatic operated ladle tilting mechanism for foundries
PH191 Automatic side stands with Breaking locking System
PH192 Hydraulic Cylinder Liner Puller
PH193 Compressed air generation using Speed Breaker
PH194 Automatic Pneumatic Chapatti making Machine
PH195 Fabrication of Vacuum assisted wall climber
PH196 Pneumatic Injection Moulding Machine
PH197 Hydraulic Hybrid System for Four Wheeler
PH198 Foot operated Hydro-Pneumatic Mechanical Pipe Vice
PH199 Automatic Pneumatic Coconut cutting Machine
PH200 Automatic Pneumatic punching and Riveting Machine
PH201 Automatic Pneumatic sheet Cutting Machine
PH202 Automatic multi point grease gun
PH203 Fabrication of Pneumatic Slotting Machine
PH204 Fabrication of Hydraulic Machine vice
PH205 Fabrication of Pneumatic disc brake
PH206 Automatic Pneumatic Speed Breaker on time demand
PH207 Remote controlled Hydraulic jack trolley
PH208 Fabrication of Pneumatic Multipurpose Machine
PH209 Fabrication of Pneumatic Mobile Crane
PH210 Fabrication of Pneumatic bell crank press
PH211 Automatic Pneumatic double axis welding Machine
PH212 Pneumatic Bearing Press and Puller
PH213 Fabrication of Pneumatic pellet press
PH214 Fabrication of Hydraulic Pipe Bending Machine
PH215 Pneumatic Automatic Vegetable Cutting Machine
PH216 Pneumatic Auto Feed Punching Machine
PH217 Fabrication of Automatic Pneumatic Hammer
PH218 Fabrication of Pneumatic Water Bottle crusher
PH219 Automatic Foot board Break System for Car
PH220 Automatic Reverse locking System using Differential unit
PH221 Hydraulic oil pump testing Equipment

Note:

Please note that the project topics on this page are only a brief list to give the students a idea about the possible projects and technologies that are available to the students for their project work. We at Ensemble offer many more projects of varying complexity under each of the above categories. If you do not find any of the above projects to your liking please contact us either over phone or through the form on the contact us page mentioning your specific requirement and we will get back to you with project topics and ideas that are more suited to your specific requirement.

Also note that the above lists contain a combination of IEEE projects and some non IEEE projects as well, for the students to choose accordingly. The IEEE based projects in the above lists are almost exclusively from IEEE 2017 base papers. The above lists are updated periodically from time to time, you are welcome to visit this page for updated project topics. Our consolidated project lists meant for the academic year 2016-17, which will include many new projects will be uploaded shortly.